Re: copy startup-config.txt between devices?

netwizz — Wed, 05 Feb 2020 20:28:24 GMT

I would typically agree with matching.

That said, all that has changed depends on how far back you go. On the 7xxx platform 08.0.70 turns on POE by default (no harm)

08.0.80 depreciates dual-mode.

If you are booting the Primary, I would leave it set to boot Default, because that means primary first.

***

The website you mentioned is pretty good, and to be honest I have yet to mount a USB stick and copy the files from there. Usually I do it with TFTP, but that's all good either way.

Usually, I just upgrade everything to the latest code before configuring it.

The thing is depending upon the version, the upgrade commands change a little...

For example, from 08.0.60x or 08.0.61x I use:
copy tftp flash 10.1.2.3 mnz10114.bin bootrom
copy tftp flash 10.1.2.3 SPR08080e.bin secondary
copy tftp flash 10.1.2.3 SPS08080e.bin primary

To verify, is more than just showing flash. The command I actually type is "verify md5 pri" or "verif md5 sec"

IF I am at 08.0.70x or later, I use this because it actually gives you control of where the image goes:

copy tftp system-manifest 10.1.2.3 FI08080e_Manifest.txt primary switch-image
copy tftp system-manifest 10.1.2.3 FI08080e_Manifest.txt secondary router-image

AFTER I get to 08.0.80x, I jump to 08.0.90x /w UFI doing this:

copy tftp flash 10.1.2.3 SPS08090eufi.bin primary
copy tftp flash 10.1.2.3 SPR08090eufi.bin secondary

*************
I actually did one today for the first time in months From out of box to 08.0.90e:

Hotplugger Daemon Initialized ..
System initialization completed...console going online.

Copyright (c) 1996-2017 Brocade Communications Systems, Inc. All rights reserved.
UNIT 1: compiled on Aug 14 2017 at 06:54:44 labeled as SPS08061a
(24723488 bytes) from Primary SPS08061a.bin
SW: Version 08.0.61aT211
Compressed Boot-Monitor Image size = 786944, Version:10.1.10T225 (mnz10110)
Compiled on Sun Jun 25 09:25:15 2017

HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module
Serial #:redacted
Current License: 2X1G
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
1000 MHz ARM processor ARMv7 88 MHz bus
8192 KB boot flash memory
2048 MB code flash memory
1024 MB DRAM
STACKID 1 system uptime is 9 second(s)
The system started at 00:02:06 GMT+00 Sat Jan 01 2000

The system : started=cold start

ICX7150-C12 Switch>
PS 1, Internal Power supply detected.
PS 1, Internal Power supply is up.
PoE Info: Adding new 54V capacity of 124000 mW, total capacity is 124000, total free capacity is 124000

ICX7150-C12 Switch>en

No password has been assigned yet...

ICX7150-C12 Switch(config)#no spanning-tree

ICX7150-C12 Switch(config)#logging console

ICX7150-C12 Switch(config)#logging persistence

ICX7150-C12 Switch(config)#ip address 10.1.2.20/21

SYSLOG: <14> Jan 1 00:04:02 Added ip address 10.1.2.20 by un-authenticated user from console session.
ICX7150-C12 Switch(config)#ip dns domain-name redacted.gov

ICX7150-C12 Switch(config)#ip dns server-address 10.4.5.6 10.4.5.7

ICX7150-C12 Switch(config)#no ip dhcp-client auto-update enable

ICX7150-C12 Switch(config)#
SYSLOG: <14> Jan 1 00:04:02 DHCPC: auto-update state was changed to disabled
no ip dhcp-client enable

ICX7150-C12 Switch(config)#ip default-gateway 10.1.2.1

ICX7150-C12 Switch(config)#clock summer-time

ICX7150-C12 Switch(config)#clock timezone us Eastern

ICX7150-C12 Switch(config)#sntp server 10.220.1.1 4

Invalid input -> sntp server 10.220.1.1 4
Type ? for a list
ICX7150-C12 Switch(config)#ntp

SYSLOG: <14> Dec 31 19:04:02 NTP: The system clock is not synchronized and does not have a reference configured.
ICX7150-C12 Switch(config-ntp)# server 10.220.1.1

SYSLOG: <14> Dec 31 19:04:02 NTP: client association is mobilized for 10.220.1.1.

SYSLOG: <14> Dec 31 19:04:02 NTP: The system clock is not synchronized to any time source.
ICX7150-C12 Switch(config-ntp)#
SYSLOG: <15> Dec 31 19:04:02 DHCPC: Stopped DHCP Client service
!

ICX7150-C12 Switch(config-ntp)#exit

ICX7150-C12 Switch(config)#exit

ICX7150-C12 Switch#
SYSLOG: <14> Dec 31 19:04:02 Security: running-config was potentially changed by operator from console

SYSLOG: <14> Dec 31 19:04:11 System: Interface ethernet 1/1/7, state up

ICX7150-C12 Switch#sh ip

Switch IP address: 10.1.2.20

Subnet mask: 255.255.248.0

Default router address: 10.1.2.1
TFTP server address: 10.1.2.3
Configuration filename: None
Image filename: spz10114.bin
IP MTU: 1500
ICX7150-C12 Switch#ping 10.1
SYSLOG: <14> Feb 5 13:47:41 Security: Time is updated by NTP server "10.220.1.1" from "19:05:14.114 Eastern Fri Dec 31 1999 " to "13:47:41.393 Eastern Wed Feb 05 2020 "
.144.4

Sending 1, 16-byte ICMP Echo to 10.1.2.3, timeout 5000 msec, TTL 64
Type Control-c to abort
Reply from 10.1.2.3 : bytes=16 time=1ms TTL=128
Success rate is 100 percent (1/1), round-trip min/avg/max=1/1/1 ms.
ICX7150-C12 Switch#copy tftp flash 10.1.2.3 spz10114.bin bootrom

ICX7150-C12 Switch#copy tftp flash 10.1.2.3 mnz10114.bin bootrom

ICX7150-C12 Switch#Load to buffer (8192 bytes per dot)
.................................
SYNCING IMAGE TO FLASH. DO NOT SWITCH OVER OR POWER DOWN THE UNIT(65536 bytes per dot)...
............
TFTP to Flash Done.
ICX7150-C12 Switch#copy tftp flash 10.1.2.3 SPS08080e.bin primary

ICX7150-C12 Switch#sh boot

Boot system preference(Configured):
Use Default

Boot system preference(Default):
Boot system flash primary
Boot system flash secondary
ICX7150-C12 Switch#sh fl

Stack unit 1:
Compressed Pri Code size = 24723488, Version:08.0.61aT211 (SPS08061a.bin)
Compressed Sec Code size = 28314668, Version:08.0.61aT213 (SPR08061a.bin)
Compressed Boot-Monitor Image size = 786432, Version:10.1.14T225
Code Flash Free Space = 1311850496

ICX7150-C12 Switch#copy tftp flash 10.1.2.3 SPS08080e.bin primary

ICX7150-C12 Switch#Load to buffer (8192 bytes per dot)
............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................
SYNCING IMAGE TO FLASH. DO NOT SWITCH OVER OR POWER DOWN THE UNIT(65536 bytes per dot)...
.............................................................................................................................................................................................................................................................................................................................................................................................................
TFTP to Flash Done.

ICX7150-C12 Switch#sh fl

Stack unit 1:
Compressed Pri Code size = 25973456, Version:08.0.80eT211 (SPS08080e.bin)
Compressed Sec Code size = 28314668, Version:08.0.61aT213 (SPR08061a.bin)
Compressed Boot-Monitor Image size = 786432, Version:10.1.14T225
Code Flash Free Space = 1311850496

ICX7150-C12 Switch#copy tftp flash 10.1.2.3 SPR08080e.bin secondary

ICX7150-C12 Switch#Load to buffer (8192 bytes per dot)
................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................
SYNCING IMAGE TO FLASH. DO NOT SWITCH OVER OR POWER DOWN THE UNIT(65536 bytes per dot)...
.......................................................................................................................................................................................................................................................................................................................................................................................................................................................................
TFTP to Flash Done.
ICX7150-C12 Switch#verif md5 pri

ICX7150-C12 Switch#............................................................................................................................................................................................................................................................................................................................................................................................................Done
Size = 25973456, MD5 03420970e5d4bb0cd48f5bc6485541a8
ICX7150-C12 Switch#verif md5 sec

ICX7150-C12 Switch#................................
SYSLOG: <14> Feb 5 13:56:14 System: Interface ethernet 1/1/7, state down
.......................................................................................................................................................................................................................................................................................................................................................................................................................................Done
Size = 29826604, MD5 82d4bd085d6b8e1616da651040d98274
ICX7150-C12 Switch#erase start

ICX7150-C12 Switch#reload

The system is going down NOW!

INFO: empty config data in the primary area, try to read from backup
INFO: empty config data in the backup area also

System initialization completed...console going online.

Copyright (c) 2017 Ruckus Wireless, Inc. All rights reserved.
UNIT 1: compiled on Apr 9 2019 at 03:09:20 labeled as SPS08080e
(25973456 bytes) from Primary SPS08080e.bin
SW: Version 08.0.80eT211
Compressed Boot-Monitor Image size = 786944, Version:10.1.14T225 (mnz10114)
Compiled on Thu Nov 15 12:59:22 2018

HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module
Serial #:Redacted
Software Package: BASE_SOFT_PACKAGE
Current License: 2X1G
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
1000 MHz ARM processor ARMv7 88 MHz bus
8192 KB boot flash memory
2048 MB code flash memory
1024 MB DRAM
STACKID 1 system uptime is 7 second(s)
The system started at 19:00:21 GMT+00 Wed Feb 05 2020

The system : started=cold start

ICX7150-C12 Switch>
Creating certificate, please wait...

SSL Client Certificate is successfully created

PS 1, Internal Power supply detected.
PS 1, Internal Power supply is up.
PoE: Stack unit 1 PS 1, Internal Power supply with 124000 mwatts capacity is up
PoE Info: Adding new 54V capacity of 124000 mW, total capacity is 124000, total free capacity is 124000
PoE Info: PoE module 1 of Unit 1 on ports 1/1/1 to 1/1/12 detected. Initializing....
2000 log entries of PoE Event Trace Log Buffer is allocated on unit 1 for unit 1
PoE Event Trace Logging enabled for unit 1
PoE Info: Current Firmware version 1.8.7, Recommended Firmware version 2.1.1, Upgrade Required.
PoE Info: PoE FW upgrade is required. Auto upgrade will start now.
Firmware version from File: 2.1.1
PoE Warning: Upgrading firmware in slot 1....DO NOT SWITCHOVER OR POWER DOWN THE UNIT.
PoE Info: FW Download on slot 1...sending download command...
PoE Info: FW Download on slot 1...TPE response received.
PoE Info: FW Download on slot 1...sending erase command...
PoE Info: FW Download on slot 1...erase command...accepted.
PoE Info: FW Download on slot 1...erasing firmware memory...
PoE Info: FW Download on slot 1...erasing firmware memory...completed
PoE Info: FW Download on slot 1...sending program command...
PoE Info: FW Download on slot 1...sending program command...accepted.
PoE Info: FW Download on slot 1...programming firmware...takes around 5 minutes....
U1-MSG: PoE Info: Firmware Download on slot 1.....10 percent completed.
U1-MSG: PoE Info: Firmware Download on slot 1.....20 percent completed.
U1-MSG: PoE Info: Firmware Download on slot 1.....30 percent completed.
U1-MSG: PoE Info: Firmware Download on slot 1.....40 percent completed.
U1-MSG: PoE Info: Firmware Download on slot 1.....50 percent completed.
U1-MSG: PoE Info: Firmware Download on slot 1.....60 percent completed.
U1-MSG: PoE Info: Firmware Download on slot 1.....70 percent completed.
U1-MSG: PoE Info: Firmware Download on slot 1.....80 percent completed.
U1-MSG: PoE Info: Firmware Download on slot 1.....90 percent completed.
U1-MSG: PoE Info: Firmware Download on slot 1.....100 percent completed.
PoE Info: FW Download on slot 1...programming firmware...completed.
PoE Info: FW Download on slot 1...upgrading firmware...completed. Module will be reset.
PoE Info: Resetting in slot 1....
PoE Info: Resetting module in slot 1....completed.
PoE Info: Programming Ruckus defaults.....
PoE Info: Programming Ruckus defaults. Step 1: Writing port defaults on module in slot 1....
PoE Info: Programming Ruckus Defaults: Step 2: Writing PM defaults on module in slot 1.
PoE Info: Programming Ruckus defaults. Step 3: Writing user byte 0xf4 on module in slot 1.
PoE Info: Programming Ruckus defaults. Step 4: Saving settings on module in slot 1.
PoE Info: Programming Ruckus defaults....completed.
PoE Info: PoE module 1 of Unit 1 initialization is done.

ICX7150-C12 Switch(config)#en

ICX7150-C12 Switch#conf t

ICX7150-C12 Switch(config)#no spanning-tree

ICX7150-C12 Switch(config)#logging console

ICX7150-C12 Switch(config)#logging persistence

ICX7150-C12 Switch(config)#ip address 10.1.2.20/21

SYSLOG: <14> Feb 5 19:06:22 Added ip address 10.1.2.20 by un-authenticated user from console session.
ICX7150-C12 Switch(config)#ip dns domain-name dhec.sc.gov

ICX7150-C12 Switch(config)#ip dns server-address 10.4.5.6 10.4.5.7

ICX7150-C12 Switch(config)#no ip dhcp-client auto-update enable

ICX7150-C12 Switch(config)#
SYSLOG: <14> Feb 5 19:06:23 DHCPC: auto-update state was changed to disabled
no ip dhcp-client enable

ICX7150-C12 Switch(config)#ip default-gateway 10.1.2.1

ICX7150-C12 Switch(config)#clock summer-time

ICX7150-C12 Switch(config)#clock timezone us Eastern

ICX7150-C12 Switch(config)#ntp

SYSLOG: <14> Feb 5 14:06:23 NTP: The system clock is not synchronized and does not have a reference configured.
ICX7150-C12 Switch(config-ntp)# server 10.220.1.1

SYSLOG: <14> Feb 5 14:06:23 NTP: client association is mobilized for 10.220.1.1.

SYSLOG: <14> Feb 5 14:06:23 NTP: The system clock is not synchronized to any time source.
ICX7150-C12 Switch(config-ntp)#!

ICX7150-C12 Switch(config-ntp)#exit

ICX7150-C12 Switch(config)#exit

ICX7150-C12 Switch#
SYSLOG: <14> Feb 5 14:06:23 Security: running-config was potentially changed by operator from console

ICX7150-C12 Switch#
SYSLOG: <14> Feb 5 14:06:24 DHCPC: protocol disabled

SYSLOG: <14> Feb 5 14:06:31 System: Interface ethernet 1/1/7, state up

SYSLOG: <14> Feb 5 14:06:32 System: PoE: Power disabled on port 1/1/7 because of detection of non-PD. PD detection will be disabled on port.

ICX7150-C12 Switch#sh fl

Stack unit 1:
NAND Type: Micron NAND 2GiB (x 1)
Compressed Pri Code size = 25973456, Version:08.0.80eT211 (SPS08080e.bin)
Compressed Sec Code size = 29826604, Version:08.0.80eT213 (SPR08080e.bin)
Compressed Boot-Monitor Image size = 786944, Version:10.1.14T225
Code Flash Free Space = 1318756352

ICX7150-C12 Switch#ping 10.1.2.3

Sending 1, 16-byte ICMP Echo to 10.1.2.3, timeout 5000 msec, TTL 64
Type Control-c to abort
Reply from 10.1.2.3 : bytes=16 time=1ms TTL=128
Success rate is 100 percent (1/1), round-trip min/avg/max=1/1/1 ms.
ICX7150-C12 Switch#copy tftp flash 10.1.2.3 SPS08090eufi.bin primary
SYSLOG: <14> Feb 5 14:07:41 Security: Time is updated by NTP server "10.220.1.1" from "14:07:40.170 Eastern Wed Feb 05 2020 " to "14:07:41.546 Eastern Wed Feb 05 2020 "

ICX7150-C12 Switch#copy tftp flash 10.1.2.3 SPS08090eufi.bin primary

ICX7150-C12 Switch#Load to buffer (8192 bytes per dot)

SYSLOG: <14> Feb 5 14:08:03 COPY IMAGE TO FLASH START
...........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

Processing the bundle image...

Flashing application image to Primary partition...

SYSLOG: <14> Feb 5 14:09:43 COPY APPLICATION IMAGE FROM BUNDLE START

SYNCING IMAGE TO FLASH. DO NOT SWITCH OVER OR POWER DOWN THE UNIT(65536 bytes per dot)...
......................................................................................................................................................................................................................................................................................................................................................................................................................................................

Flashing bootrom image...

SYSLOG: <14> Feb 5 14:10:12 COPY BOOTROM IMAGE FROM BUNDLE START

SYNCING IMAGE TO FLASH. DO NOT SWITCH OVER OR POWER DOWN THE UNIT(65536 bytes per dot)...
............

Post processing bundle image...

Bundle image processed successfully
ICX7150-C12 Switch#
SYSLOG: <14> Feb 5 14:10:20 COPY BUNDLE IMAGE COMPLETED

ICX7150-C12 Switch#sh fl

Stack unit 1:
NAND Type: Micron NAND 2GiB (x 1)
Compressed Pri Code size = 28674200, Version:08.0.90eT211 (SPS08090e.bin)
Compressed Sec Code size = 29826604, Version:08.0.80eT213 (SPR08080e.bin)
Compressed Boot-Monitor Image size = 786432, Version:10.1.15T225
Code Flash Free Space = 1277210624
ICX7150-C12 Switch#copy tftp flash 10.1.2.3 SPR08090eufi.bin secondary

ICX7150-C12 Switch#Load to buffer (8192 bytes per dot)
.
SYSLOG: <14> Feb 5 14:11:29 COPY IMAGE TO FLASH START
.....................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

Processing the bundle image...

Flashing application image to Secondary partition...

SYSLOG: <14> Feb 5 14:13:20 COPY APPLICATION IMAGE FROM BUNDLE START

SYNCING IMAGE TO FLASH. DO NOT SWITCH OVER OR POWER DOWN THE UNIT(65536 bytes per dot)...
.................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

Flashing bootrom image...

SYSLOG: <14> Feb 5 14:13:53 COPY BOOTROM IMAGE FROM BUNDLE START

SYNCING IMAGE TO FLASH. DO NOT SWITCH OVER OR POWER DOWN THE UNIT(65536 bytes per dot)...
............

Post processing bundle image...

Bundle image processed successfully
ICX7150-C12 Switch#
SYSLOG: <14> Feb 5 14:14:01 COPY BUNDLE IMAGE COMPLETED

ICX7150-C12 Switch#sh fl

Stack unit 1:
NAND Type: Micron NAND 2GiB (x 1)
Compressed Pri Code size = 28674200, Version:08.0.90eT211 (SPS08090e.bin)
Compressed Sec Code size = 32550404, Version:08.0.90eT213 (SPR08090e.bin)
Compressed Boot-Monitor Image size = 786432, Version:10.1.15T225
Code Flash Free Space = 1230946304
ICX7150-C12 Switch#
SYSLOG: <14> Feb 5 14:14:14 System: Interface ethernet 1/1/7, state down

ICX7150-C12 Switch#erase start

ICX7150-C12 Switch#reload

System initialization completed...console going online.

Successfully notified stack role 'none' to hm

Copyright (c) Ruckus Networks, Inc. All rights reserved.
UNIT 1: compiled on Nov 19 2019 at 04:11:53 labeled as SPS08090e
(28674200 bytes) from Primary SPS08090e.bin (UFI)
SW: Version 08.0.90eT211
Compressed Secondary Boot Code size = 786944, Version:10.1.15T225 (mnz10115)
Compiled on Thu Jan 31 07:08:55 2019

HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module
Serial #:Redacted
Software Package: BASE_SOFT_PACKAGE
Current License: 2X1G
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
1000 MHz ARM processor ARMv7 88 MHz bus
8192 KB boot flash memory
2048 MB code flash memory
1024 MB DRAM
STACKID 1 system uptime is 8 second(s)
The system started at 19:17:15 GMT+00 Wed Feb 05 2020

The system : started=warm start reloaded=by "reload"

Press Enter key to login
Debug: Feb 5 19:17:17 read_private_key_from_tpm, TPM Engine Init Done..!!

Creating certificate, please wait...

SSL Client Certificate is successfully created

Press Enter key to login

PS 1, Internal Power supply detected.
PS 1, Internal Power supply is up.
PoE: Stack unit 1 PS 1, Internal Power supply with 124000 mwatts capacity is up
PoE Info: Adding new 54V capacity of 124000 mW, total capacity is 124000, total free capacity is 124000

RSA Key pair is successfully created
ICX7150-C12 SwitchPoE Info: PoE module 1 of Unit 1 on ports 1/1/1 to 1/1/12 detected. Initializing....
2000 log entries of PoE Event Trace Log Buffer is allocated on unit 1 for unit 1
PoE Event Trace Logging enabled for unit 1
PoE Info: PoE module 1 of Unit 1 initialization is done.

User Access Verification

Please Enter Login Name:

topic Re: copy startup-config.txt between devices? in ICX Switches

copy startup-config.txt between devices?

Re: copy startup-config.txt between devices?

Re: copy startup-config.txt between devices?

Re: copy startup-config.txt between devices?

Re: copy startup-config.txt between devices?