topic Re: Smartzone 100 dont start services in SmartZone and Virtual SmartZone

Smartzone 100 dont start services

rommel_silva — Fri, 01 Nov 2019 19:10:41 GMT

Hi everyone. I am new on Ruckus community and I am having problem to access web interface of my smartzone 100 controller. After a reboot I cant get access web page. SSH access is working normally. When I access the controller through ssh port i see that all services are down ("# show service" command). I already tried to UP services with the command "# service start" but even after several hours the session still shows me the following information: "Wait for (list of services) up. This list of services decreases right after the start of execution of command but then remains unchanged or even increases (as can be seen in the attached image). Looks like some service can't startup.
Is it possible that the controller is in some kind of "Maintenance Mode"? If so, is there a command to take the controller out of maintenance mode? Is there any other command I can run to know what is going on with the controller? Thank you very much for any help.

Rommel

Re: Smartzone 100 dont start services

Vineet_nejwala — Sat, 02 Nov 2019 04:38:10 GMT

Hello Rommel,

Looks like either the SZ went into "Crash mode" or "Maintenance mode" . The clearing of the controller from "Crash mode" or "Maintenance mode" can only be done through shell mode to which Ruckus engineer's have access. Kindly log a case with Ruckus so that we can clear the status on the controller and bring all services back online.

You can open a case either by online using below link and filling your details:

https://support.ruckuswireless.com/cases/new

or you can call our support line and an Admin team member would log a case for you as per your details provided.

https://support.ruckuswireless.com/contact-us

Best Regards
Vineet

Re: Smartzone 100 dont start services

rommel_silva — Sat, 02 Nov 2019 09:25:10 GMT

Hi Vineet,

Thanks for answer me.
Is there no shell command to check if the controller is in crash mode or maintenance mode?

Even turning off the controller is not enough to take it out of this mode?
Is there really nothing I can do without help of a ruckus engineer?

Best regards

Tommel

Re: Smartzone 100 dont start services

jardel_almeida1 — Sat, 02 Nov 2019 10:47:13 GMT

Infelizmente somente com um TAC suporte Ruckus via shell. Isso já aconteceu, comigo também.

Re: Smartzone 100 dont start services

rommel_silva — Sat, 02 Nov 2019 12:32:38 GMT

Jardel,

Você tem uma controladora SZ100 em operação?
Tem um contrato de suporte ativo com a Ruckus?
Teria alguma forma de contactá-lo diretamente para trocar algumas informações?

Obrigado.

Re: Smartzone 100 dont start services

Vineet_nejwala — Sat, 02 Nov 2019 12:57:16 GMT

Hello Rommel,

Unfortunately this can only be validated from shell mode or you can perform a Factory reset on the controller but this would wipe all of the configuration from the controller and everything would be needed to configure from scratch (this would still not be a 100% that issue will be resolved). So the best and safest option is to log a ticket with Ruckus support and let an TAC engineer resolve this issue for you.

Best Regards
Vineet

Re: Smartzone 100 dont start services

bradley_wilson — Mon, 02 Aug 2021 16:23:20 GMT

You can use command # show cluster-state and it will provide output as follows:

Current Management Service Status : Out of service
Current Node Status : Out of service
Cluster Status : Out of service
Cluster Operation : None
System Mode : Crash

Cluster Node Information
----------------------------------------------------------------
No. Name Role
----- ------------------------ -----------
1 cluster1 LEADER

Re: Smartzone 100 dont start services

derek_small — Fri, 18 Mar 2022 16:30:45 GMT

I'm in the same boat after two controller lost contact for a few seconds. What a POS!!!