topic Re: what is this problem ? in SmartZone and Virtual SmartZone

what is this problem ?

lasha_chavleshv — Fri, 09 Feb 2018 16:53:47 GMT

Feb 8 08:44:03 RuckusAP daemon.err wsgclient[464]: crSocketInit:243 crSocketConn failed ret = 124
Feb 8 08:44:03 RuckusAP daemon.err wsgclient[464]: cmrInit:138 Call 'crDefSocketInit()' failed, ip:10.1.115.16 port:443, ret:124/CR initial socket failed
Feb 8 08:44:03 RuckusAP daemon.err wsgclient[464]: communicatorInit:364 Init connection failed, ret:124, connectRetry:459
Feb 8 08:44:03 RuckusAP daemon.err wsgclient[464]: registration:594 Failed to init socket! ret:124 url:https://10.1.115.16/wsg/ap
Feb 8 08:44:05 RuckusAP daemon.info hub_registrar: OCSP: 'unknown' on ap-registrar.ruckuswireless.com - withhold query
Feb 8 08:44:08 RuckusAP daemon.err wsgclient[464]: crSocketConn:56 errno:103/Software caused connection abort
Feb 8 08:44:08 RuckusAP daemon.err wsgclient[464]: crSocketInit:243 crSocketConn failed ret = 124
Feb 8 08:44:08 RuckusAP daemon.err wsgclient[464]: cmrInit:138 Call 'crDefSocketInit()' failed, ip:10.1.115.16 port:443, ret:124/CR initial socket failed
Feb 8 08:44:08 RuckusAP daemon.err wsgclient[464]: communicatorInit:364 Init connection failed, ret:124, connectRetry:460
Feb 8 08:44:08 RuckusAP daemon.err wsgclient[464]: registration:594 Failed to init socket! ret:124 url:https://10.1.115.16/wsg/ap
Feb 8 08:44:13 RuckusAP daemon.err wsgclient[464]: crSocketConn:56 errno:103/Software caused connection abort
Feb 8 08:44:13 RuckusAP daemon.err wsgclient[464]: crSocketInit:243 crSocketConn failed ret = 124
Feb 8 08:44:13 RuckusAP daemon.err wsgclient[464]: cmrInit:138 Call 'crDefSocketInit()' failed, ip:10.1.115.16 port:443, ret:124/CR initial socket failed
Feb 8 08:44:13 RuckusAP daemon.err wsgclient[464]: communicatorInit:364 Init connection failed, ret:124, connectRetry:461
Feb 8 08:44:13 RuckusAP daemon.err wsgclient[464]: registration:594 Failed to init socket! ret:124 url:https://10.1.115.16/wsg/ap

Re: what is this problem ?

lasha_chavleshv — Fri, 09 Feb 2018 16:55:01 GMT

ap not join on virtual smart zone 3.6

Re: what is this problem ?

wesley_xavier — Fri, 09 Feb 2018 18:04:34 GMT

Try reset AP to factory defaults and change the firmware to standalone and join the smartzone again

Re: what is this problem ?

lasha_chavleshv — Mon, 12 Feb 2018 11:18:29 GMT

i reseted aps , change firmware to standalone , but still a problem on virtual smart zone ,
virtual smart zone block all port , i do not use firewall my network .

i did it via cli

vSZ# config

vSZ (config)# lwapp2scg

vSZ (config-lwapp2scg)# policy accept-all

i still a problem , aps not join virtual smart zone , version 3.5.1.0.862

Re: what is this problem ?

hyosang_choi — Tue, 13 Feb 2018 14:31:13 GMT

Try below command.

conf
no ap-cert-check

The AP's cert may old cert.

Re: what is this problem ?

lasha_chavleshv — Tue, 13 Feb 2018 15:01:49 GMT

i did it , but not work 😞
virtual smart zone block port 443 , i not use firewall
ap directli connect virtual machine

Re: what is this problem ?

john_spiteri — Wed, 21 Feb 2018 10:06:14 GMT

any solution for the above ?

Re: what is this problem ?

lasha_chavleshv — Wed, 21 Feb 2018 10:12:17 GMT

i can not join ap on Virtual smart zone (high Scale)

Re: what is this problem ?

lasha_chavleshv — Wed, 21 Feb 2018 10:54:41 GMT

when i on Tunnel WLAN traffic through Ruckus GRE , clint not get ip address
no used nat , not used firewall

Re: what is this problem ?

sunny_gupta — Thu, 12 Apr 2018 06:02:05 GMT

I had the same issue today. the correct resolution was to disable the ap cert check on the sz controller using the command above 'no ap-cert-check'. You need CLI access to the controller and log in to privileged mode to execute the command.

Some more detail is available here with this workaround and the fix:
https://support.ruckuswireless.com/answers/000005390?_ga=2.129584140.1025065841.1523453190-121888804...

cheers

Re: what is this problem ?

michael_brado — Thu, 12 Apr 2018 21:16:54 GMT

And then upgrade your AP certificates...