topic Re: Access point not automatically connecting in RUCKUS Support for Lennar Homes

Access point not automatically connecting

Dtolomeo — Sun, 28 May 2023 20:48:04 GMT

New Lennar home owner - I have so far been able to get the master access point up and working - how do I connect the other two access points ? I followed the steps in

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/Physical-Factory-Reset-an-Access-Points-Ruckus/td-p/47056

step 8 says the other access points should automatically connect but they are not doing so. I started over and repeated the steps even two more times and nothing.

please help

Re: Access point not automatically connecting

Dtolomeo — Mon, 29 May 2023 14:09:44 GMT

Actually as I looked again, I did gateway setup to get the master to work - if I do typical setup and app always gives an error right at the end that it will not connect - strangely my wifi is working but there is still the confirgure.me option when I search the wifi… more lost than before

Re: Access point not automatically connecting

Imran_ruckus — Mon, 29 May 2023 15:49:03 GMT

Hi @Dtolomeo

Thank you for contacting Lennar Home Community.

Hope you are doing well!!!

Thank you for the detailed information you shared,

As per the case description, I could understand that you are unable to get the Access Points working after performing a factory reset.

Please follow the below process to factory reset your APs to configure them with a new SSID.

IMPORTANT NOTE: To perform a factory reset correctly on one of the access points, you must disconnect the rest of your other access points from the "ICX-7150-switch". For example, if you have 3 access points, you should go to the switch and disconnect 2 of the cables to turn off the "2 access points" and only leave 1 connected with which we are going to work the factory reset once you configure the access point and make sure all is good, go ahead and reconnect the other Access Points back.

Physical Factory Reset of RUCKUS Access Point:

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/Physical-Factory-Reset-an-Access-Points-Ruckus/td-p/47056

Ruckus Unleashed Set-up using your Mobile:

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/Ruckus-Unleashed-Set-up-using-your-Mobile/td-p/47086

Ruckus Unleashed Set-up using Web:

https://www.youtube.com/watch?v=j8I5aVwMNMg

Password recovery setup:

https://www.youtube.com/watch?v=sqnG8fupaLk

Please let me know if you have any queries in this regard.

Thank you again for your patience.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

Re: Access point not automatically connecting

Dtolomeo — Tue, 30 May 2023 01:42:58 GMT

Do I need a router to do the typical install ? I have a modem, a switch, and 3 access points. After typical installation I am unable to connect to the wifi I created , after gateway installation I can connect to wifi but the other access points are not connecting automatically

Re: Access point not automatically connecting

Imran_ruckus — Tue, 30 May 2023 15:09:26 GMT

Hi @Dtolomeo

Greetings!!!

Thank you for the response.

If your ISP modem is directly connected to the ICX-7150-C12P Switch, it doesn’t work only with Modem. The connection must be from a Router or Modem-Router combo device.

Please refer to the short guide link below about how to connect the devices as a reference:

Most common Setups for Lennar homes users:

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/Most-common-Setups-for-Lenna...

Please confirm and let me know if you have any queries in this regard.

Thank you again for your patience.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.