topic Can't upgrade ICX 7150 to image 8095g - The code type 64 is not correct for the target hardware in RUCKUS Support for Lennar Homes

Can't upgrade ICX 7150 to image 8095g - The code type 64 is not correct for the target hardware

Rjndael — Mon, 24 Apr 2023 08:04:06 GMT

PoE has recently went offline on my Ruckus 7150 switch. When I connect to the console I see the following error messages:
> Vmain (48V) fault has forced all ports on slot 0 to lose power.

I've attempted to upgrade the image to version 8095g over TFTP as advised in https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/POE-Fatal-message-is-flooding-console-on-ICS7150-c12-switch/m-p/51365

When I enter the upgrade command, I get the following error:
--------------

copy tftp flash 192.168.0.9 SPS08095gufi.bin bootrom
telnet@ruckus-switch#The code type 64 is not correct for the target hardware, abort!
File Type Check Failed

--------------

Version:
--------------

telnet@ruckus-switch#show version
Copyright (c) 1996-2017 Brocade Communications Systems, Inc. All rights reserved.
UNIT 1: compiled on Aug 14 2017 at 06:54:44 labeled as SPS08061a
(24723488 bytes) from Primary SPS08061a.bin
SW: Version 08.0.61aT211
Compressed Boot-Monitor Image size = 786944, Version:10.1.10T225 (mnz10110)
Compiled on Sun Jun 25 09:25:15 2017

HW: Stackable ICX7150-C12-POE

-------------

Tried upgrading to 08070c and 08070aa, similar message, but the code is 33 instead.

Tried upgrading to 08080f first, as advised in the link. Tried all 4 images, received the following errors:

-------

telnet@ruckus-switch#copy tftp flash 192.168.0.9 SPS08080f.bin bootrom
telnet@ruckus-switch#The code type 33 is not correct for the target hardware, ab ort!
File Type Check Failed

TFTP to Flash Error - code 8
telnet@ruckus-switch#copy tftp flash 192.168.0.9 SPS08080fufi.bin bootrom
telnet@ruckus-switch#The code type 64 is not correct for the target hardware, ab ort!
File Type Check Failed

TFTP to Flash Error - code 8
telnet@ruckus-switch#copy tftp flash 192.168.0.9 SPR08080fufi.bin bootrom
telnet@ruckus-switch#The code type 64 is not correct for the target hardware, ab ort!
File Type Check Failed

TFTP to Flash Error - code 8
telnet@ruckus-switch#copy tftp flash 192.168.0.9 SPR08080f.bin bootrom
telnet@ruckus-switch#The code type 33 is not correct for the target hardware, ab ort!
File Type Check Failed

TFTP to Flash Error - code 8

------

Please advise.

Re: Can't upgrade ICX 7150 to image 8095g - The code type 64 is not correct for the target hardware

wmckennaiv — Mon, 24 Apr 2023 12:27:52 GMT

Same exact thing for me.

Re: Can't upgrade ICX 7150 to image 8095g - The code type 64 is not correct for the target hardware

Jayavidhya — Mon, 24 Apr 2023 18:03:18 GMT

Hi @Rjndael

Greetings of the day,

Please upgrade the switch twice using the following path .

Code>08080f>08095g using the file SPS08095gufi.bin in both partition primary and secondary

copy rftp flash 192.168.0.9 spz10106.bin bootrom

copy tftp flash 192.168.0.9 SPS08080f.bin primary

Show flash (ensure that you have the new flash code)

Write memory

reload

Now you can go to the recommended code:

copy tftp flash 192.168.0.9 SPR08095gufi.bin primary

copy tftp flash 192.168.0.9 SPR08095gufi.bin secondary

Show flash (ensure that you have the new flash code)

Write memory

Reload

How to Upgrade a Switch ICX-7150-C12P using a USB flash drive

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Upgrade-a-Switch-ICX-...

How to upgrade a Switch ICX7150-C12P via TFTP

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Upgrade-a-Switch-ICX-...

Best regards,

Jayavidhya

Lennar Home Community

Re: Can't upgrade ICX 7150 to image 8095g - The code type 64 is not correct for the target hardware

Rjndael — Tue, 25 Apr 2023 02:55:11 GMT

I've managed to do the upgrade.

In order to roll on 08080f, I've used the following commands:

copy rftp flash 192.168.0.9 mnz10114.bin bootrom

copy tftp flash 192.168.0.9 SPS08080f.bin primary

You can find the mnz10114.bin in the Boot directory in the 08080f.zip. Then I've restarted the router and rolled on 08095g just to the primary:

copy tftp flash 192.168.0.9 SPR08095gufi.bin primary

Rebooted one more time. After the update, the switch would take a while to startup, since it is going to update firmware of the components, which takes around 10 minutes.

After the restart, PoE works flawlessly. The problem is fixed.

Re: Can't upgrade ICX 7150 to image 8095g - The code type 64 is not correct for the target hardware

Jayavidhya — Tue, 25 Apr 2023 12:16:19 GMT

Hi @Rjndael

I am so glad to hear that the issue got resolved.

Thanks for letting us know.

Please let us know if you have any queries in this regard.

Best regards,

Jayavidhya

Lennar Home Community

Re: Can't upgrade ICX 7150 to image 8095g - The code type 64 is not correct for the target hardware

Isai_Roa — Fri, 30 Jun 2023 18:27:10 GMT

Hi.

How to you used rftp?

In the Switch they show me that command isn't possible

SW_RUCKUS_DATACENTER#copy rftp flash
Invalid input -> rftp flash
Type ? for a list

Re: Can't upgrade ICX 7150 to image 8095g - The code type 64 is not correct for the target hardware

Imran_ruckus — Fri, 30 Jun 2023 18:34:01 GMT

Hi @Isai_Roa

Greetings!!!

Thank you for contacting RUCKUS Lennar Home Community.

Hope you are doing well

Please note it is tftp and not rftp

As this case is raised by @Rjndael

If you are a Lennar Home RUCKUS device user, to avoid confusion with posts please raise your own post/case on 'RUCKUS Lennar Support', and a detailed description of the network issue and what you've done so that we can guide you properly.

Thank you again for understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.