topic Re: Unleashed AP in RUCKUS Support for Lennar Homes

Unleashed AP

thetrifakta — Thu, 16 Mar 2023 21:21:39 GMT

I have a Ruckus switch and AP in the new build with Lennar. I also run a Nest mesh network. My Ruckus network shows available but connected devices have no internet service and two yellow light show on the AP. If I log into the Unleashed app, the lights on the AP are green and internet service is available. Once I log off the app, the lights go yellow again with no service. This happened out of the blue. My mesh network runs well with no concerns. I have had this set up for 2 years and this just occurred a few weeks ago. I searched the forum for this issue with no luck so apologies if this is a duplicate issue. I am also not very tech savvy. Thank you in advance.

Re: Unleashed AP

Imran_ruckus — Thu, 16 Mar 2023 22:38:42 GMT

Hi @thetrifakta

Thank you for contacting Lennar Home Community.

Hope you are doing well!!!

Thank you for the detailed information you shared,

From the case description, I could understand that you are unable to connect devices using RUCKUS Access Points.

Seems like your AP light status is in normal condition. (Please refer to the below link)

https://docs.commscope.com/bundle/unleashed-200.9-onlinehelp/page/GUID-19D4261B-D10B-4DE3-B63A-3498F80103D0.html

Could you please let us know?

1. Was there any Power outage just before you started facing this issue?

2. Is your Internet Connection from the Internet Service Provider (ISP) stable and working? (You could check this by connecting to your local router Wi-Fi or from an ethernet cable from Router to a laptop/PC)

Please let us know the answers to the above queries or if you have any queries in this regard.

Thank you again.

Best regards,

Imran Sanadi

Lennar Home Community.

Re: Unleashed AP

thetrifakta — Fri, 24 Mar 2023 16:38:57 GMT

Thank you for the response. It appears that there is service running to the AP, the lights were yellow because there were no clients/devices connected to the network. The network is incredibly slow even with up to 1000Mbs of download speed and most sites. I did an AP reboot through the unleashed app and everything is now restarting. Thank you

Re: Unleashed AP

Imran_ruckus — Fri, 24 Mar 2023 17:55:39 GMT

Hi @thetrifakta

Greetings!!!

Thank you for the detailed information you shared,

If your internet connection is stable from the ISP (Internet Service Provider) and there is a unstable internet from the Switch,

This may happen when the Switch runs on the Routing code. The Switch should run on the Switching code to avoid these issues for Lennar home users. If the Switch boots up on the other partition (Due to a power outage/power spike may be) which may be running on a ‘Routing Code’ results in causing this issue.

You can take Console access to the switch in order to verify, if the switch is able to connect properly to Access Points or if it has a ‘Routing Code’ issue which happens due to power outages/ power spikes most of the time, this is a known issue for Lennar home users.

An identifier of this problem is that it comes out as Switch-Router in the unleashed dashboard.

There we are going to see 2 important things the

-MAC address: Physical address of the device this never changes

- An IP address is a unique address (logical) that identifies a device on the internet or a local network like your home (this can change and may not be the same as the one shown on the dashboard)

There are multiple ways to fix this issue as described in below steps:

Please follow the below steps:

1. To fix this issue, we must identify the ‘current’ IP address assigned by your local router to the switch ICX-7150-C12P

I will leave you a guide on how to perform an IP scanner on your local network to identify the switch IP address very easily.

How to find my Ruckus “Devices IP address” using free applications:

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-find-my-Ruckus-Devices-IP-address-using-free-applications/td-p/47027

2. Once we identify the IP address of the switch proceed to access remotely to the device “Command Line”

How to remotely access to 'ICX 7150-C12P' or 'access points' "Network devices":

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-remotely-access-to-ICX-7150-12P-or-access-points-quot/td-p/47388

If you can access the Command line should look like this:

ICX7150-C12 Router>

3. Here is a quick guide for understanding how to fix the 'routing code issue' however, you only need to run the following commands once you are on the command line 'CLI'

Note: Hit Enter to accept each command

enable

show version

copy flash flash secondary

boot system flash secondary yes

(Please share the output screenshot of the ‘show version’ command to check your current Switch version, if the upgrade is needed to avoid this problem in the future)

Example:

VIDEO LINK AS REFERENCE: https://www.youtube.com/watch?v=Eem1IBgYaWc

ICX7150-24P Router>enable (hit enter to accept the command)
ICX7150-24P Router#copy flash flash secondary (hit enter to accept the command and wait: until the flash finished)
ICX7150-24P Router#boot system flash secondary yes (hit enter to accept the command: the switch will reboot)

There are Two ways:

I) How to Fix Routing code issues on Lennar Home users via CLI

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Fix-Routing-code-issues-on-Lennar-Home-users/td-p/47305

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-solve-the-routing-code-issue-in-your-ICX7150-Switch/td-p/47335

II) Or WEB access option

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Fix-Routing-code-issues-on-Lennar-Home-users-via-Web-GUI/m-p/47959#M1998

4. If access via IP address is not possible here is a guide on how to access to the Switch via console (cable access between your PC to the ICX 7150-C12P) in this case we need a USB type C to USB standard or Console cable Rj45 to USB.

How to console in the ICX-7150-C12P

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-console-in-the-ICX-7150-12c-using-a-Windows-Machine/td-p/46759

Once you are logged in to the ICX-7150-C12P please follow and perform the same commands that are on point '3'

Please let me know if you have any queries in this regard.

Best regards,

Imran Sanadi

Lennar Home Community.