topic Re: POE Failure in RUCKUS Support for Lennar Homes

POE Failure

mccrackens — Sat, 01 Aug 2026 22:03:26 GMT

I have an ICX 7150-C12P switch in a Lennar Home setup. The PoE controller is failing, causing connected Access Points to lose power. Attempting to modify or save inline power configuration triggers a fatal SIGNUM#11 kernel panic and core dump even after a full erase startup-config factory reset. Going through all the troubleshooting online has told me that I most likely have a chip failure

Re: POE Failure

MariaC862 — Mon, 03 Aug 2026 19:59:45 GMT

Hi Mccrackens,

Thank you for your post. Could you please share an image of the error message?

Please confirm if PoE is enabled, as shown on this guide: https://community.ruckuswireless.com/t5/RUCKUS-Lennar-Support-Knowledge/NO-Power-on-Access-Points-and-ICX-7150-C12P-Switch-with-GREEN/ta-p/72186

If PoE is enabled, then please share these outputs:

show inline power detail

show log

show inline power

show version

You may need this guide: https://community.ruckuswireless.com/t5/RUCKUS-Lennar-Support-Knowledge/How-to-access-the-Command-Line-Interface-CLI-of-the-RUCKUS-ICX/ta-p/74450

I recommend these steps to collect the logs easily on a single file: How To Capture PUTTY Session Log

Let me know how it goes and if you have any questions.

Re: POE Failure

Yarenis — Wed, 05 Aug 2026 17:07:14 GMT

Hi @mccrackens

Greetings!!!

I trust this message finds you well.

I kindly request an update on the status of the issue so that we may proceed further with resolving it.

Thank you.

Best regards,
Yarenis Hernández
RUCKUS | Lennar Home Community Support

Re: POE Failure

mccrackens — Thu, 06 Aug 2026 01:49:01 GMT

Hello Maria,

Please see log below.

ICX7150-C12-Switch#enable

Incomplete command.

ICX7150-C12-Switch#show inline power detail

Power Supply Data On unit 1:

++++++++++++++++++

Power Supply Data:

++++++++++++++++++

Power Supply #1:

Max Curr: 2.3 Amps

Voltage: 54.0 Volts

Capacity: 124 Watts

PoePower: 124 Watts

POE Details Info. On Unit 1 :

General PoE Data:

+++++++++++++++++

--More--, next page: Space, next line: Return key, quit: Control-c Firmware

Version

----------------

02.1.0 Build 002

Hardware

Version

----------------

V2R4

Cumulative Port State Data:

+++++++++++++++++++++++++++

#Ports #Ports #Ports #Ports #Ports #Ports #Ports

Admin-On Admin-Off Oper-On Oper-Off Off-Denied Off-No-PD Off-Fault

-------------------------------------------------------------------------

12 0 2 10 0 9 1

Cumulative Port Power Data:

--More--, next page: Space, next line: Return key, quit: Control-c +++++++++++++++++++++++++++

#Ports #Ports #Ports Power Power

Pri: 1 Pri: 2 Pri: 3 Consumption Allocation

-----------------------------------------------

0 0 12 6.500 W 30.800 W

ICX7150-C12-Switch# show log

Syslog logging: enabled ( 0 messages dropped, 0 flushes, 0 overruns)

Buffer logging: level ACDMEINW, 106 messages logged

level code: A=alert C=critical D=debugging M=emergency E=error

I=informational N=notification W=warning

Static Log Buffer:

Jan 1 08:18:23:I:System: Stack unit 1 POE PS 1, Internal Power supply with 124000 mwatts capacity is up

Dynamic Log Buffer (4000 lines):

Jan 5 06:10:31:I:Security: console login by un-authenticated console user to PRIVILEGED EXEC mode

Jan 4 14:27:28:I:STP: VLAN 1 Port 1/2/1 Bridge TC Event (FwdDlyExpiry)

Jan 4 14:27:28:I:STP: VLAN 1 Port 1/2/1 STP State -> FORWARDING (FwdDlyExpiry)

Jan 4 14:27:13:I:STP: VLAN 1 Port 1/2/1 STP State -> LEARNING (FwdDlyExpiry)

Jan 4 14:27:10:I:STP: VLAN 1 Port 1/2/1 STP State -> LISTENING (MakeFwding)

Jan 4 14:27:10:I:System: Interface ethernet 1/2/1, state up

Jan 4 14:27:02:I:System: Interface ethernet 1/2/1, state down

Jan 4 14:27:02:I:STP: VLAN 1 Port 1/2/1 STP State -> DISABLED (PortDown)

Jan 4 14:27:02:I:STP: VLAN 1 Port 1/2/1 STP State -> LEARNING (PortDown)

Jan 4 14:26:56:I:STP: VLAN 1 Port 1/2/1 STP State -> LEARNING (FwdDlyExpiry)

Jan 4 14:26:54:I:STP: VLAN 1 Port 1/2/1 STP State -> LISTENING (MakeFwding)

Jan 4 14:26:54:I:System: Interface ethernet 1/2/1, state up

Jan 4 14:26:46:I:System: Interface ethernet 1/2/1, state down

Jan 4 14:26:46:I:STP: VLAN 1 Port 1/2/1 STP State -> DISABLED (PortDown)

--More--, next page: Space, next line: Return key, quit: Control-c Jan 4 14:26:46:I:STP: VLAN 1 Port 1/2/1 STP State -> LISTENING (PortDown)

Jan 4 14:26:45:I:STP: VLAN 1 Port 1/2/1 STP State -> LISTENING (MakeFwding)

Jan 4 14:26:45:I:System: Interface ethernet 1/2/1, state up

Jan 4 14:26:35:I:System: Interface ethernet 1/2/1, state down

Jan 4 14:26:35:I:STP: VLAN 1 Port 1/2/1 STP State -> DISABLED (PortDown)

Jan 4 14:26:35:I:STP: VLAN 1 Port 1/2/1 STP State -> LEARNING (PortDown)

Jan 4 14:26:35:I:STP: VLAN 1 Port 1/2/1 STP State -> LEARNING (FwdDlyExpiry)

Jan 4 14:26:33:I:STP: VLAN 1 Port 1/2/1 STP State -> LISTENING (MakeFwding)

Jan 4 14:26:33:I:System: Interface ethernet 1/2/1, state up

Jan 4 14:26:22:I:System: Interface ethernet 1/2/1, state down

Jan 4 14:26:22:I:STP: VLAN 1 Port 1/2/1 STP State -> DISABLED (PortDown)

Jan 4 14:26:22:I:STP: VLAN 1 Port 1/2/1 STP State -> FORWARDING (PortDown)

Jan 4 14:25:50:I:STP: VLAN 1 Port 1/2/1 STP State -> FORWARDING (FwdDlyExpiry)

Jan 4 14:25:48:I:STP: VLAN 1 Port 1/2/1 STP State -> LEARNING (FwdDlyExpiry)

Jan 4 14:25:45:I:STP: VLAN 1 Port 1/2/1 STP State -> LISTENING (MakeFwding)

Jan 4 14:25:45:I:System: Interface ethernet 1/2/1, state up

Jan 4 14:25:38:I:System: Interface ethernet 1/2/1, state down

Jan 4 14:25:38:I:STP: VLAN 1 Port 1/2/1 STP State -> DISABLED (PortDown)

Jan 4 14:25:38:I:STP: VLAN 1 Port 1/2/1 STP State -> FORWARDING (PortDown)

Jan 4 14:25:29:I:STP: VLAN 1 Port 1/2/1 STP State -> FORWARDING (FwdDlyExpiry)

Jan 4 14:25:27:I:STP: VLAN 1 Port 1/2/1 STP State -> LEARNING (FwdDlyExpiry)

Jan 4 14:25:25:I:STP: VLAN 1 Port 1/2/1 STP State -> LISTENING (MakeFwding)

Jan 4 14:25:25:I:System: Interface ethernet 1/2/1, state up

--More--, next page: Space, next line: Return key, quit: Control-c Jan 4 14:25:22:I:System: Interface ethernet 1/2/1, state down

Jan 4 14:25:22:I:STP: VLAN 1 Port 1/2/1 STP State -> DISABLED (PortDown)

Jan 4 14:25:22:I:STP: VLAN 1 Port 1/2/1 STP State -> FORWARDING (PortDown)

Jan 4 14:25:02:I:STP: VLAN 1 Port 1/2/1 STP State -> FORWARDING (FwdDlyExpiry)

Jan 4 14:25:00:I:STP: VLAN 1 Port 1/2/1 STP State -> LEARNING (FwdDlyExpiry)

Jan 4 14:24:58:I:STP: VLAN 1 Port 1/2/1 STP State -> LISTENING (MakeFwding)

Jan 4 14:24:58:I:System: Interface ethernet 1/2/1, state up

Jan 4 14:24:16:I:System: Interface ethernet 1/2/1, state down

Jan 4 14:24:16:I:STP: VLAN 1 Port 1/2/1 STP State -> DISABLED (PortDown)

Jan 4 14:24:16:I:STP: VLAN 1 Port 1/2/1 STP State -> FORWARDING (PortDown)

Jan 4 04:27:31:I:System: Interface ethernet 1/1/11, state down

Jan 4 04:27:31:I:STP: VLAN 1 Port 1/1/11 STP State -> DISABLED (PortDown)

Jan 4 04:27:31:I:STP: VLAN 1 Port 1/1/11 STP State -> FORWARDING (PortDown)

Jan 1 08:21:37:D:DHCPC: TFTP unable to download running-configuration

Jan 1 08:21:20:D:DHCPC: sending TFTP request for bootfile name brocade.cfg

Jan 1 08:21:02:D:DHCPC: sending TFTP request for bootfile name default.cfg

Jan 1 08:20:45:D:DHCPC: sending TFTP request for bootfile name ICX7150-C12-Switch.cfg

Jan 1 08:20:28:D:DHCPC: sending TFTP request for bootfile name ICX7150-C12-Switchc0c5.2095.fe37.cfg

Jan 1 08:20:11:D:DHCPC: sending TFTP request for bootfile name ICX7150-C12-Switchc0c5.2095.fe37-config.cfg

Jan 1 08:19:54:D:DHCPC: sending TFTP request for bootfile name ICX7150-C12-Switchc0c5.2095.fe37-config.cfg

Jan 1 08:19:40:I:STP: VLAN 1 Port 1/1/2 STP State -> FORWARDING (FwdDlyExpiry)

Jan 1 08:19:39:I:STP: VLAN 1 Port 1/1/1 STP State -> FORWARDING (FwdDlyExpiry)

Jan 1 08:19:38:I:STP: VLAN 1 Port 1/1/2 STP State -> LEARNING (FwdDlyExpiry)

--More--, next page: Space, next line: Return key, quit: Control-c Jan 1 08:19:38:D:DHCPC: sending TFTP request for bootfile name ICX7150-C12-Switchc0c5.2095.fe37-config.cfg

Jan 1 08:19:37:I:STP: VLAN 1 Port 1/1/1 STP State -> LEARNING (FwdDlyExpiry)

Jan 1 08:19:35:I:STP: VLAN 1 Port 1/1/2 STP State -> LISTENING (MakeFwding)

Jan 1 08:19:35:I:System: Interface ethernet 1/1/2, state up

Jan 1 08:19:35:I:STP: VLAN 1 Port 1/1/1 STP State -> LISTENING (MakeFwding)

Jan 1 08:19:35:I:System: Interface ethernet 1/1/1, state up

Jan 1 08:19:32:I:System: Interface ethernet 1/1/2, state down

Jan 1 08:19:32:I:STP: VLAN 1 Port 1/1/2 STP State -> DISABLED (PortDown)

Jan 1 08:19:32:I:STP: VLAN 1 Port 1/1/2 STP State -> FORWARDING (PortDown)

Jan 1 08:19:31:I:System: Interface ethernet 1/1/1, state down

Jan 1 08:19:31:I:STP: VLAN 1 Port 1/1/1 STP State -> DISABLED (PortDown)

Jan 1 08:19:31:I:STP: VLAN 1 Port 1/1/1 STP State -> FORWARDING (PortDown)

Jan 1 08:19:22:D:DHCPC: sending TFTP request for bootfile name ICX7150-C12-Switchc0c5.2095.fe37-config.cfg

Jan 1 08:19:06:D:DHCPC: sending TFTP request for bootfile name ICX7150-C12-Switchc0c5.2095.fe37-config.cfg

Jan 1 08:18:52:I:STP: VLAN 1 Port 1/1/2 STP State -> FORWARDING (FwdDlyExpiry)

Jan 1 08:18:52:I:STP: VLAN 1 Port 1/1/1 STP State -> FORWARDING (FwdDlyExpiry)

Jan 1 08:18:50:I:STP: VLAN 1 Port 1/1/2 STP State -> LEARNING (FwdDlyExpiry)

Jan 1 08:18:50:I:STP: VLAN 1 Port 1/1/1 STP State -> LEARNING (FwdDlyExpiry)

Jan 1 08:18:49:I:DHCPC: ICX7150-C12-Switch configured with ip-address 10.0.0.6; subnet mask 255.255.255.0

Jan 1 08:18:49:D:DHCPC: sending TFTP request for bootfile name ICX7150-C12-Switchc0c5.2095.fe37-config.cfg

Jan 1 08:18:49:I:STP: VLAN 1 Port 1/1/9 STP State -> FORWARDING (FwdDlyExpiry)

Jan 1 08:18:48:I:STP: VLAN 1 Port 1/1/2 STP State -> LISTENING (MakeFwding)

Jan 1 08:18:48:I:System: Interface ethernet 1/1/2, state up

--More--, next page: Space, next line: Return key, quit: Control-c Jan 1 08:18:48:I:STP: VLAN 1 Port 1/1/1 STP State -> LISTENING (MakeFwding)

Jan 1 08:18:48:I:System: Interface ethernet 1/1/1, state up

Jan 1 08:18:47:I:STP: VLAN 1 Port 1/1/9 STP State -> LEARNING (FwdDlyExpiry)

Jan 1 08:18:45:I:System: PoE: Power disabled on port 1/1/9 because of detection of non-PD. PD detection will be disabled on port.

Jan 1 08:18:45:I:STP: VLAN 1 Port 1/1/9 STP State -> LISTENING (MakeFwding)

Jan 1 08:18:45:I:System: Interface ethernet 1/1/9, state up

Jan 1 08:18:42:I:System: PoE: Power enabled on port 1/1/2.

Jan 1 08:18:42:I:System: PoE: Power enabled on port 1/1/1.

Jan 1 08:18:40:I:STP: VLAN 1 Port 1/2/1 Bridge TC Event (FwdDlyExpiry)

Jan 1 08:18:40:I:STP: VLAN 1 Port 1/2/1 STP State -> FORWARDING (FwdDlyExpiry)

Jan 1 08:18:27:I:STP: VLAN 1 Port 1/1/11 STP State -> FORWARDING (FwdDlyExpiry)

Jan 1 08:18:25:I:STP: VLAN 1 Port 1/2/1 STP State -> LEARNING (FwdDlyExpiry)

Jan 1 08:18:25:I:STP: VLAN 1 Port 1/1/11 STP State -> LEARNING (FwdDlyExpiry)

Jan 1 08:18:23:I:System: Stack unit 1 POE PS 1, Internal Power supply with 124000 mwatts capacity is up

Jan 1 08:18:23:I:STP: VLAN 1 Port 1/2/1 STP State -> LISTENING (MakeFwding)

Jan 1 08:18:23:I:System: Interface ethernet 1/2/1, state up

Jan 1 08:18:23:I:STP: VLAN 1 Port 1/1/11 STP State -> LISTENING (MakeFwding)

Jan 1 08:18:23:I:System: Interface ethernet 1/1/11, state up

Jan 1 08:18:21:I:PKI: Trustpoint DEVICE_TRUSTPNT: error: File not loaded, Manufacturing certificate expired.

Jan 1 08:18:19:I:System: Warm start

Jan 1 08:18:19:D:DHCPC: starting dhcp client service

Jan 1 08:18:19:I:DHCPC: Found dynamic IP address 10.0.0.6 subnet mask 255.255.255.0 on port 1/1/1

Jan 1 08:18:19:I:Security: running-config was potentially changed by operator from console

ICX7150-C12-Switch#show l inline power

Power Capacity: Total is 124000 mWatts. Current Free is 93200 mWatts.

Power Allocations: Requests Honored 11 times

Port Admin Oper ---Power(mWatts)--- PD Type PD Class Pri Fault/

State State Consumed Allocated Error

--------------------------------------------------------------------------

1/1/1 On On 3300 15400 802.3af Class 3 3 n/a

1/1/2 On On 3200 15400 802.3af Class 3 3 n/a

1/1/3 On Off 0 0 n/a n/a 3 n/a

1/1/4 On Off 0 0 n/a n/a 3 n/a

1/1/5 On Off 0 0 n/a n/a 3 n/a

1/1/6 On Off 0 0 n/a n/a 3 n/a

1/1/7 On Off 0 0 n/a n/a 3 n/a

1/1/8 On Off 0 0 n/a n/a 3 n/a

1/1/9 On Non-PD 0 0 n/a n/a 3 n/a

1/1/10 On Off 0 0 n/a n/a 3 n/a

1/1/11 On Off 0 0 n/a n/a 3 n/a

1/1/12 On Off 0 0 n/a n/a 3 n/a

--------------------------------------------------------------------------

Total 6500 30800

--More--, next page: Space, next line: Return key, quit: Control-c

ICX7150-C12-Switch#show version

UNIT 1: compiled on Nov 20 2018 at 00:09:55 labeled as SPS08080d

(25968884 bytes) from Primary SPS08080d.bin

SW: Version 08.0.80dT211

Compressed Boot-Monitor Image size = 786944, Version:10.1.14T225 (mnz10114)

Compiled on Thu Nov 15 12:59:22 2018

HW: Stackable ICX7150-C12-POE

==========================================================================

UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module

Serial #:FEK3803R265

Software Package: BASE_SOFT_PACKAGE

Current License: 2X1G

P-ASIC 0: type B160, rev 11 Chip BCM56160_B0

==========================================================================

UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module

==========================================================================

UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module

==========================================================================

1000 MHz ARM processor ARMv7 88 MHz bus

8192 KB boot flash memory

2048 MB code flash memory

1024 MB DRAM

--More--, next page: Space, next line: Return key, quit: Control-c STACKID 1 system uptime is 3 day(s) 22 hour(s) 43 second(s)

The system started at 08:22:57 GMT+00 Sat Jan 01 2000

The system : started=warm start reloaded=by "reload"

ICX7150-C12-Switch#

Re: POE Failure

mccrackens — Thu, 06 Aug 2026 01:59:41 GMT

Hello

Please see above

Re: POE Failure

Yarenis — Thu, 06 Aug 2026 15:02:30 GMT

Hi @mccrackens

Please upgrade the switch, as I can see the unit is constantly dropping connection. If the issue persists after the upgrade, we will need to check uplink port 1/2/1. Below are the commands to run if the problem continues post-upgrade:

How to upgrade RUCKUS ICX-7150-C12P from Non-Unified Forwarding Image (UFI) to a stable UFI version

https://community.ruckuswireless.com/t5/RUCKUS-Lennar-Support-Knowledge/How-to-upgrade-RUCKUS-ICX-7150-C12P-from-Non-Unified-Forwarding/ta-p/71353

show version

show flash

show log

show interface ethernet 1/2/2

Best regards,
Yarenis Hernández
RUCKUS | Lennar Home Community Support

Re: POE Failure

mccrackens — Fri, 07 Aug 2026 03:41:04 GMT

Hello Yarenis,

The update for firmware is complete. It does look like it did go down again as it did with the old firmware but I am unsure if this is just part of the updating.

ICX7150-C12-Switch#show version
Copyright (c) Ruckus Networks, Inc. All rights reserved.
UNIT 1: compiled on May 6 2022 at 23:24:50 labeled as SPS08095g
(31457280 bytes) from Primary SPS08095g.bin (UFI)
SW: Version 08.0.95gT211
Compressed Secondary Boot Code size = 786944, Version:10.1.24T225 (mnz10124)
Compiled on Thu Apr 21 06:08:52 2022

HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module
Serial #:FEK3803R265
Software Package: BASE_SOFT_PACKAGE
Current License: 2X1G
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
1000 MHz ARM processor ARMv7 88 MHz bus
8 MB boot flash memory
2 GB code flash memory
1 GB DRAM
STACKID 1 system uptime is 13 minute(s) 54 second(s)
The system started at 23:26:35 GMT+00 Fri May 06 2022

The system : started=warm start reloaded=by "reload"

ICX7150-C12-Switch#show flash
Stack unit 1:
NAND Type: Micron NAND 2GiB (x 1)
Compressed Pri Code size = 31457280, Version:08.0.95gT211 (SPS08095g.bin)
Compressed Sec Code size = 31457280, Version:08.0.95gT211 (SPS08095g.bin)
Compressed Pri Boot Code size = 786944, Version:10.1.14T225 (mnz10114)
Compressed Sec Boot Code size = 786944, Version:10.1.24T225 (mnz10124)
Code Flash Free Space = 1099591680
ICX7150-C12-Switch#show log
Syslog logging: enabled ( 0 messages dropped, 0 flushes, 0 overruns)
Buffer logging: level ACDMEINW, 69 messages logged
level code: A=alert C=critical D=debugging M=emergency E=error
I=informational N=notification W=warning

Static Log Buffer:
May 6 23:25:01:I:System: Stack unit 1 POE PS 1, Internal Power supply with 124000 mwatts capacity is up

Dynamic Log Buffer (4000 lines):
May 6 23:37:44:I:STP: VLAN 1 Port 1/1/2 STP State -> FORWARDING (FwdDlyExpiry)
May 6 23:37:44:I:STP: VLAN 1 Port 1/1/1 STP State -> FORWARDING (FwdDlyExpiry)
May 6 23:37:42:I:STP: VLAN 1 Port 1/1/2 STP State -> LEARNING (FwdDlyExpiry)
May 6 23:37:42:I:STP: VLAN 1 Port 1/1/1 STP State -> LEARNING (FwdDlyExpiry)
May 6 23:37:40:I:STP: VLAN 1 Port 1/1/2 STP State -> LISTENING (MakeFwding)
May 6 23:37:40:I:System: Interface ethernet 1/1/2, state up
May 6 23:37:39:I:STP: VLAN 1 Port 1/1/1 STP State -> LISTENING (MakeFwding)
May 6 23:37:39:I:System: Interface ethernet 1/1/1, state up
May 6 23:37:36:I:System: Interface ethernet 1/1/1, state down
May 6 23:37:36:I:STP: VLAN 1 Port 1/1/1 STP State -> DISABLED (PortDown)
May 6 23:37:36:I:STP: VLAN 1 Port 1/1/1 STP State -> FORWARDING (PortDown)
May 6 23:37:35:I:System: Interface ethernet 1/1/2, state down
May 6 23:37:35:I:STP: VLAN 1 Port 1/1/2 STP State -> DISABLED (PortDown)
May 6 23:37:35:I:STP: VLAN 1 Port 1/1/2 STP State -> FORWARDING (PortDown)
May 6 23:36:58:I:STP: VLAN 1 Port 1/1/1 STP State -> FORWARDING (FwdDlyExpiry)
May 6 23:36:56:I:STP: VLAN 1 Port 1/1/2 STP State -> FORWARDING (FwdDlyExpiry)
May 6 23:36:56:I:STP: VLAN 1 Port 1/1/1 STP State -> LEARNING (FwdDlyExpiry)
May 6 23:36:54:I:STP: VLAN 1 Port 1/1/2 STP State -> LEARNING (FwdDlyExpiry)
May 6 23:36:53:I:STP: VLAN 1 Port 1/1/1 STP State -> LISTENING (MakeFwding)
May 6 23:36:53:I:System: Interface ethernet 1/1/1, state up
May 6 23:36:52:I:STP: VLAN 1 Port 1/1/2 STP State -> LISTENING (MakeFwding)
May 6 23:36:52:I:System: Interface ethernet 1/1/2, state up
May 6 23:36:46:I:System: PoE: Power enabled on port 1/1/2.
May 6 23:36:45:I:System: PoE: Power enabled on port 1/1/1.
May 6 23:36:21:I:System: U1-MSG: PoE Info: Firmware Download on slot 1.....100 percent completed.
May 6 23:35:16:I:System: U1-MSG: PoE Info: Firmware Download on slot 1.....90 percent completed.
May 6 23:34:10:I:System: U1-MSG: PoE Info: Firmware Download on slot 1.....80 percent completed.
May 6 23:33:19:I:Security: console login by un-authenticated console user to PRIVILEGED EXEC mode
May 6 23:33:04:I:System: U1-MSG: PoE Info: Firmware Download on slot 1.....70 percent completed.
May 6 23:31:59:I:System: U1-MSG: PoE Info: Firmware Download on slot 1.....60 percent completed.
May 6 23:31:55:I:Security: telnet terminated by un-authenticated telnet user from src IP 10.0.0.137 from src MAC f0a6.5429.4df9 from USER EXEC mode
May 6 23:30:52:I:System: U1-MSG: PoE Info: Firmware Download on slot 1.....50 percent completed.
May 6 23:29:57:I:COPY BUNDLE IMAGE COMPLETED
May 6 23:29:49:I:COPY BOOTROM IMAGE FROM BUNDLE START
May 6 23:29:46:I:System: U1-MSG: PoE Info: Firmware Download on slot 1.....40 percent completed.
May 6 23:28:56:I:COPY APPLICATION IMAGE FROM BUNDLE START
May 6 23:28:28:I:System: U1-MSG: PoE Info: Firmware Download on slot 1.....30 percent completed.
May 6 23:28:21:D:DHCPC: TFTP unable to download running-configuration
May 6 23:28:03:D:DHCPC: sending TFTP request for bootfile name brocade.cfg
May 6 23:27:44:D:DHCPC: sending TFTP request for bootfile name default.cfg
May 6 23:27:26:D:DHCPC: sending TFTP request for bootfile name ICX7150-C12-Switch.cfg
May 6 23:27:22:I:System: U1-MSG: PoE Info: Firmware Download on slot 1.....20 percent completed.
May 6 23:27:08:D:DHCPC: sending TFTP request for bootfile name ICX7150-C12-Switchc0c5.2095.fe37.cfg
May 6 23:26:50:D:DHCPC: sending TFTP request for bootfile name ICX7150-C12-Switchc0c5.2095.fe37-config.cfg
May 6 23:26:36:I:COPY IMAGE TO FLASH START
May 6 23:26:33:D:DHCPC: sending TFTP request for bootfile name ICX7150-C12-Switchc0c5.2095.fe37-config.cfg
May 6 23:26:16:D:DHCPC: sending TFTP request for bootfile name ICX7150-C12-Switchc0c5.2095.fe37-config.cfg
May 6 23:26:15:I:System: U1-MSG: PoE Info: Firmware Download on slot 1.....10 percent completed.
May 6 23:26:02:I:Security: telnet login by un-authenticated telnet user from src IP 10.0.0.137 from src MAC f0a6.5429.4df9 to PRIVILEGED EXEC mode
May 6 23:25:59:D:DHCPC: sending TFTP request for bootfile name ICX7150-C12-Switchc0c5.2095.fe37-config.cfg
May 6 23:25:56:I:Security: telnet login by un-authenticated telnet user from src IP 10.0.0.137 from src MAC f0a6.5429.4df9 to USER EXEC mode
May 6 23:25:42:D:DHCPC: sending TFTP request for bootfile name ICX7150-C12-Switchc0c5.2095.fe37-config.cfg
May 6 23:25:31:I:STP: VLAN 1 Port 1/1/9 STP State -> FORWARDING (FwdDlyExpiry)
May 6 23:25:28:I:STP: VLAN 1 Port 1/1/9 STP State -> LEARNING (FwdDlyExpiry)
May 6 23:25:25:I:STP: VLAN 1 Port 1/1/9 STP State -> LISTENING (MakeFwding)
May 6 23:25:25:I:System: Interface ethernet 1/1/9, state up
May 6 23:25:24:I:DHCPC: ICX7150-C12-Switch configured with ip-address 10.0.0.6; subnet mask 255.255.255.0
May 6 23:25:24:D:DHCPC: sending TFTP request for bootfile name ICX7150-C12-Switchc0c5.2095.fe37-config.cfg
May 6 23:25:07:I:STP: VLAN 1 Port 1/2/1 STP State -> FORWARDING (FwdDlyExpiry)
May 6 23:25:05:I:STP: VLAN 1 Port 1/2/1 STP State -> LEARNING (FwdDlyExpiry)
May 6 23:25:03:I:STP: VLAN 1 Port 1/2/1 STP State -> LISTENING (MakeFwding)
May 6 23:25:03:I:System: Interface ethernet 1/2/1, state up
May 6 23:25:03:W:System: PoE Warning: Upgrading firmware in slot 65537....DO NOT SWITCHOVER OR POWER DOWN THE UNIT.
May 6 23:25:02:I:System: Warm start
May 6 23:25:02:I:PKI: Trustpoint DEVICE_TRUSTPNT: Successfully loaded Manufacturing certificate file.
May 6 23:25:01:I:System: Stack unit 1 POE PS 1, Internal Power supply with 124000 mwatts capacity is up
May 6 23:24:59:D:DHCPC: starting dhcp client service
May 6 23:24:59:I:DHCPC: Found dynamic IP address 10.0.0.6 subnet mask 255.255.255.0 on port 1/1/1
May 6 23:24:57:I:Security: running-config was potentially changed by un-authenticated user from console
ICX7150-C12-Switch#show interface ethernet 1/2/2
GigabitEthernet1/2/2 is down, line protocol is down
Port down for 14 minute(s) 37 second(s)
Hardware is GigabitEthernet, address is c0c5.2095.fe45 (bia c0c5.2095.fe45)
Configured speed auto, actual unknown, configured duplex fdx, actual unknown
Configured mdi mode AUTO, actual unknown
PTP Feature Disabled
Untagged member of L2 VLAN 1, port state is BLOCKING
BPDU guard is Disabled, ROOT protect is Disabled, Designated protect is Disabled
Link Error Dampening is Disabled
STP configured to ON, priority is level0, mac-learning is enabled
MACsec is Disabled
Flow Control is config enabled, oper enabled, negotiation disabled
Mirror disabled, Monitor disabled
Mac-notification is disabled
VLAN-Mapping is disabled
Not member of any active trunks
Not member of any configured trunks
No port name
IPG MII 96 bits-time, IPG GMII 96 bits-time
MTU 1500 bytes
MMU Mode is Store-and-forward
300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization
300 second output rate: 0 bits/sec, 0 packets/sec, 0.00% utilization
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 multicasts, 0 unicasts
0 input errors, 0 CRC, 0 frame, 0 ignored
0 runts, 0 giants
0 packets output, 0 bytes, 0 underruns
Transmitted 0 broadcasts, 0 multicasts, 0 unicasts
0 output errors, 0 collisions
Relay Agent Information option: Disabled
Protected: No
MAC Port Security: Disabled

This port is not being monitored for queue drops
Egress queues:
Queue counters Queued packets Dropped Packets
0 0 0
1 0 0
2 0 0
3 0 0
4 0 0
5 0 0
6 0 0
7 0 0

ICX7150-C12-Switch#