topic Re: ICX7150 won't factory reset; need RMA in RUCKUS Support for Lennar Homes

ICX7150 won't factory reset; need RMA

pearcebchris — Thu, 07 May 2026 20:54:56 GMT

I followed all the posts to factory reset my ICX7150, but it won't reset. It seems this is common issue.

Additionally, I see text output via console cable on MobaXTerm, but it doesn't allow keyboard input (thus why I'm trying to factory reset it). I made sure the terminal settings were correct based off other support forums here, but to cover all bases, I tried several different combinations of baud rates and other settings.

I made sure the drivers were installed - also based off of support forums here.

I tried to do an RMA since this device is clearly defective, but that went as well as you'd expect for a "Lennar" purchased product, so now I'm trying to do a convoluted RMA request through this support forum as instructed by Ruckus support.

Re: ICX7150 won't factory reset; need RMA

Imran_ruckus — Thu, 07 May 2026 21:00:30 GMT

Hi @pearcebchris

Greetings!!!

Thank you for reaching out to the RUCKUS Lennar Home Community.

We appreciate your patience and understanding as we work to resolve the issues you are experiencing with your RUCKUS setup.

Based on the information provided, it appears that you are trying to factory reset the RUCKUS ICX-7150-C12P Switch.

We apologize for any inconvenience this has caused and are committed to assisting you promptly.

To better assist you, could you please provide the following information:

1. Was there any power outages before the issue began?

2. Is your RUCKUS Switch stuck in boot mode? To confirm the same please provide a photo showing the status of the lights and the full switch panel with cable connections to the switch ports.

Please log into your RUCKUS Account before uploading these photos/screenshots.

Please help me with the above queries and should you have any further questions or concerns, feel free to reach out.

We appreciate your cooperation and look forward to resolving this matter for you promptly.

Best regards,
Imran Sanadi
RUCKUS | Lennar Home Community Support

Re: ICX7150 won't factory reset; need RMA

pearcebchris — Fri, 08 May 2026 16:56:46 GMT

No, it's not stuck in a boot loop. I can see text output via MobaXTerm when I plug in a console cable, but it doesn't accept keyboard input despite having the correct terminal settings. It boots up to the point where I can see I can type in text, but it doesn't let me, which is why I was trying to do a factory reset, but it won't factory reset either.

Re: ICX7150 won't factory reset; need RMA

Imran_ruckus — Fri, 08 May 2026 17:01:17 GMT

Hi @pearcebchris

Thank you for the response and the update.

Could you please share a picture of your RUCKUS ICX-7150-C12P Switch showing light status and cable connections?

Thank you again.

Best regards,
Imran Sanadi
RUCKUS | Lennar Home Community Support

Re: ICX7150 won't factory reset; need RMA

pearcebchris — Fri, 08 May 2026 23:29:53 GMT

Re: ICX7150 won't factory reset; need RMA

Imran_ruckus — Mon, 11 May 2026 12:41:31 GMT

Hi @pearcebchris

Greetings!!!

Thank you for your recent correspondence and update.

As per the light status of the Switch it is in a normal state. We may need to check some configurations of your RUCKUS ICX-7150-C12P Switch to troubleshoot this issue.

To proceed with troubleshooting the issue, please follow the steps outlined below to access the Command Line Interface (CLI) and provide the necessary command outputs:

1. First, identify the current IP address assigned to the switch ICX-7150-C12P by your local router. You can use an IP scanner tool to easily locate the switch's IP address on your network. Here is a guide on how to perform this using IP Scanner free applications:

https://community.ruckuswireless.com/t5/RUCKUS-Lennar-Support-Knowledge/How-to-find-the-IP-Address-of-the-RUCKUS-Devices-Switch-and-APs/ta-p/77863

2. Once you have identified the IP address of the switch, proceed to access the Command Line Interface (CLI) of the RUCKUS ICX-7150-C12P switch. Here is a guide on how to access the CLI:

https://community.ruckuswireless.com/t5/RUCKUS-Lennar-Support-Knowledge/How-to-access-the-Command-Line-Interface-CLI-of-the-RUCKUS-ICX/ta-p/74450

If you can access the Command line the prompt should look like below:

ICX7150-C12 Router> OR

ICX7150-C12 Switch>

3. After successfully accessing the CLI, please execute the following commands and provide the outputs:

enable

show version

show flash

show inline power

show inline power detail

show interface brief

Please share the command outputs or screenshots if you encounter any issues or errors during these steps.

Feel free to reach out if you have any questions or require further assistance.

Thank you for your cooperation and patience.

Best regards,
Imran Sanadi
RUCKUS | Lennar Home Community Support

Re: ICX7150 won't factory reset; need RMA

pearcebchris — Mon, 11 May 2026 13:20:57 GMT

Yep, I previously tried that. It has a password that I didn't set and it's not one of the "commonly used" Lennar passwords. Which is also why I'm trying to factory reset it, which still doesn't work, which is why I need an RMA

Re: ICX7150 won't factory reset; need RMA

Imran_ruckus — Mon, 11 May 2026 17:36:21 GMT

Hi @pearcebchris

Thank you for your response and the update.

Apologies, but as per our support policies, we are unable to process an RMA for software-related issues that can potentially be resolved through troubleshooting.

If SSH access is not working, please try using Telnet instead, as it does not require a username or password (please refer to the screenshot below).

Telnet – Port 23 (If SSH doesn’t work)

If that also does not work, please try resetting the username and password by following the process explained in the video below:

https://www.youtube.com/watch?v=XJS28DWbHM4

Please let me know how it goes.

Thank you again for your patience and understanding.

Best regards,
Imran Sanadi
RUCKUS | Lennar Home Community Support

Re: ICX7150 won't factory reset; need RMA

pearcebchris — Tue, 12 May 2026 16:25:33 GMT

You'll have to forgive me, I should have started by saying I work in IT as a Senior Network and Systems Administrator; I know how to ssh/telnet into physical devices since I do this for a living. I say that in case someone else in the future comes across this thread looking for answers who has already tried the same things I have, and for the sake of letting Imran and future techs know: I've already tried following every article, youtube video, forum, and subreddit prior to reaching out through this online forum because I know what I'm doing; I manage switches for a living, and reaching out through this support channel was my very last ditch effort because I knew I would have to go through the motions of scripted tier 1 support. I know Imran couldn't possibly have known that, and I'm trying to be patient in regards to that and their company policy, but what bothers me is we're now going in circles because, as I've mentioned previously, I can't send keyboard input when using Putty nor MobaXTerm despite making sure the terminal settings are set correctly and drivers are installed, which is partially why I was trying to do a factory reset. And in my mind, having it show green lights and everything "working" doesn't hold any value at all because the factory reset button doesn't even work, which is literally the most basic function any device could have.

I can't send keyboard input even though I can see text output (so I know the terminal settings are correct), I can't change the password, and I can't factory reset it. By all means, if we can figure out how to get around those three issues, I'm every bit as willing to try.

And in case it wasn't clear and in response to the previous message: telnet won't accept keyboard input either.

Re: ICX7150 won't factory reset; need RMA

Imran_ruckus — Wed, 13 May 2026 12:27:53 GMT

Hi @pearcebchris

Greetings!!!

Thank you for sharing the requested information.

Based on the troubleshooting performed, your ICX-7150-C12P Switch is not responding properly, and seems to be Switch corrupt image.

As a result, this Switch unit appears to be defective and needs to be replaced through the RMA (Return Merchandise Authorization) process.

To initiate the replacement, Please use the private chat option to respond so we can proceed further. For your reference, I have included a screenshot below.

Please let me know if you have any queries in this regard.

Thank you again for your patience and understanding.

Best regards,
Imran Sanadi
RUCKUS | Lennar Home Community Support

Re: ICX7150 won't factory reset; need RMA

Imran_ruckus — Fri, 15 May 2026 18:31:47 GMT

Hi @pearcebchris

Greetings!

I’ve raised an RMA case and sent you a private message with the RMA details. You will receive further notifications from the RMA case. Please check and let me know if you have any questions.

Thank you once again for your patience.

If your issue has been fully addressed, please click the Kudos button and mark the responses as an Accepted Solutions.

Best regards,
Imran Sanadi
RUCKUS | Lennar Home Community Support