topic Re: Poe turns off everytime switch reboots in RUCKUS Support for Lennar Homes

Poe turns off everytime switch reboots

jcortez5501 — Tue, 10 Jun 2025 01:10:23 GMT

Everytime the the switch loses power, when it reboots the POE feature for the access points does not activate causing me to have to connect to the switch and use putty to reactivate it. Is there a way to set the switch so this does not happen?

Re: Poe turns off everytime switch reboots

Imran_ruckus — Tue, 10 Jun 2025 13:06:37 GMT

Hi @jcortez5501

Greetings!!!

Thank you for reaching out to the RUCKUS Lennar Home Community.

We appreciate your patience and understanding as we work to resolve the issues you are experiencing with your RUCKUS setup.

Based on the information provided, it appears that you are encountering issues with RUCKUS Switch PoE.

We apologize for any inconvenience this has caused and are committed to assisting you promptly.

We may need to check some configurations of your RUCKUS ICX-7150-C12P Switch to troubleshoot this issue.

To proceed with troubleshooting the issue, please follow the steps outlined below to access the Command Line Interface (CLI) and provide the necessary command outputs:

1. First, identify the current IP address assigned to the switch ICX-7150-C12P by your local router. You can use an IP scanner tool to easily locate the switch's IP address on your network. Here is a guide on how to perform this using IP Scanner free applications:

https://community.ruckuswireless.com/t5/RUCKUS-Lennar-Support-Knowledge/How-to-find-the-IP-Address-of-the-RUCKUS-Devices-Switch-and-APs/ta-p/77863

2. Once you have identified the IP address of the switch, proceed to access the Command Line Interface (CLI) of the RUCKUS ICX-7150-C12P switch. Here is a guide on how to access the CLI:

https://community.ruckuswireless.com/t5/RUCKUS-Lennar-Support-Knowledge/How-to-access-the-Command-Line-Interface-CLI-of-the-RUCKUS-ICX/ta-p/74450

If you can access the Command line the prompt should look like below:

ICX7150-C12 Router> OR

ICX7150-C12 Switch>

3. After successfully accessing the CLI, please execute the following commands and provide the outputs:

enable

show version

show flash

show inline power

show inline power detail

show interface brief

Please share the command outputs or screenshots if you encounter any issues or errors during these steps.

Feel free to reach out if you have any questions or require further assistance.

Thank you for your cooperation and patience.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community

Re: Poe turns off everytime switch reboots

Imran_ruckus — Thu, 12 Jun 2025 12:24:06 GMT

Hi @jcortez5501

Greetings!!!

I trust this message finds you well.

I kindly request an update on the status of the issue so that we may proceed further with resolving it.

Thank you.

Best regards,
Imran Sanadi
RUCKUS | Lennar Home Community Support

Re: Poe turns off everytime switch reboots

Imran_ruckus — Mon, 16 Jun 2025 12:51:49 GMT

Hi @jcortez5501

Greetings!!!

I trust this message finds you well.

I kindly request an update on the status of the issue so that we may proceed further with resolving it.

Thank you.

Best regards,
Imran Sanadi
RUCKUS | Lennar Home Community Support

Re: Poe turns off everytime switch reboots

Imran_ruckus — Wed, 18 Jun 2025 12:36:16 GMT

Hi @jcortez5501

Greetings!!!

I trust this message finds you well.

I kindly request an update on the status of the issue so that we may proceed further with resolving it.

If we do not receive a response from you within 24 hours from the timestamp of this message, your case will proceed to closure.

Thank you.

Best regards,
Imran Sanadi
RUCKUS | Lennar Home Community Support