topic Re: 7150 corrupt mount error in RUCKUS Support for Lennar Homes

7150 corrupt mount error

mrozone — Tue, 04 Mar 2025 22:22:44 GMT

After a power outage and a reset we are still getting the following errors

what is our next step?

Re: 7150 corrupt mount error

pinky_ruckus — Wed, 05 Mar 2025 13:55:37 GMT

Hi @mrozone ,

Greetings!!!

Thank you for contacting RUCKUS Lennar Home Community.

I hope you are doing well!!!

Thank you for the information you shared.

As per the case description, I understand that your RUCKUS setup is not working and you are getting corrupt mount error.

Could you please let us know the answers to the below queries to assist you better?

1) On your switch while it's plugged into the outlet, do you see any lights on? (Amber or green) Please let us know which lights are on. (Please refer to the below picture and share a picture of the same, showing the light status and the FULL Switch panel cable connections to the Switch ports)

Please help us with pictures of your ICX-7150-C12P Switch showing the status of the lights and cable connections to the Switch ports.

Before uploading the photos please log in to the RUCKUS account and you can upload the image.

Please let us know the answers to ALL the above queries or let us know if you have any queries in this regard.

Best regards,

Pinky Rajendran

RUCKUS Lennar Home Community.

Re: 7150 corrupt mount error

mrozone — Thu, 06 Mar 2025 17:31:24 GMT

Re: 7150 corrupt mount error

mrozone — Thu, 06 Mar 2025 16:15:22 GMT

Here is a picture of the front

the cable goes to a att modem and the port is not coming online. I have tested the cable/port on the modem and it comes up plugged into a laptop.

Re: 7150 corrupt mount error

Imran_ruckus — Thu, 06 Mar 2025 18:33:16 GMT

Hi @mrozone

Greetings!!!

Thank you for your recent correspondence and update.

As per the light status of the RUCKUS ICX-7150-C12P Switch, it seems normal.

However, we may need to check some configurations of your RUCKUS ICX-7150-C12P Switch to troubleshoot this issue through CLI using the Switch's IP Address.

To proceed with troubleshooting the issue, please follow the steps outlined below to access the Command Line Interface (CLI) and provide the necessary command outputs:

1. First, identify the current IP address assigned to the switch ICX-7150-C12P by your local router. You can use an IP scanner tool to easily locate the switch's IP address on your network. Here is a guide on how to perform this using IP Scanner free applications:

https://community.ruckuswireless.com/t5/RUCKUS-Lennar-Support-Knowledge/How-to-find-the-IP-Address-of-the-RUCKUS-Devices-Switch-and-APs/ta-p/77863

2. Once you have identified the IP address of the switch, proceed to access the Command Line Interface (CLI) of the RUCKUS ICX-7150-C12P switch. Here is a guide on how to access the CLI:

https://community.ruckuswireless.com/t5/RUCKUS-Lennar-Support-Knowledge/How-to-access-the-Command-Line-Interface-CLI-of-the-RUCKUS-ICX/ta-p/74450

If you can access the Command line the prompt should look like below:

ICX7150-C12 Router> OR

ICX7150-C12 Switch>

3. After successfully accessing the CLI, please execute the following commands and provide the outputs:

enable

show version

show flash

show inline power

show inline power detail

show interface brief

Please share the command outputs or screenshots if you encounter any issues or errors during these steps.

Feel free to reach out if you have any questions or require further assistance.

Thank you for your cooperation and patience.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community

Re: 7150 corrupt mount error

mrozone — Thu, 06 Mar 2025 23:14:37 GMT

my config is default. no ip no nothing. I tried to use backup, thats corrupt too. If you take a look at the original posting, is it normal for all volumes to be corrupt?

Re: 7150 corrupt mount error

Imran_ruckus — Fri, 07 Mar 2025 12:26:06 GMT

Hi @mrozone

Greetings!!!

Thank you for the response and the update.

If you are unable to get the IP address of the Switch, please try getting console access to the Switch and help me with the command outputs I shared previously.

Here is a guide on how to access to the Switch via console (cable access between your PC to the ICX 7150-C12P) in this case, we need a USB type C to USB standard OR Console cable Rj45 to USB (Any one cable- please refer the guide)

How to console in the ICX-7150-C12P

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-console-in-the-ICX-7150-12c-using-a-Windows-Machine/td-p/46759

1. Once again, please make sure to download the zip drive for the file below & "extract all". Once it's extracted, run the file, the driver should be installed using the 2 links below.

Link 1: https://support.ruckuswireless.com/software/1414-brocade-ruckus-7150-usb-serial-driver-windows

Link 2: silabs.com/developers/usb-to-uart-bridge-vcp-drivers?tab=downloads

Once installed restart your laptop and try to locate the COM port details under 'Ports (COM & LTP)' with cables connected between the Laptop and the Switch (Refer to the below screenshot), Please check and let me know if that works.

If you have already tried the above process, please share pictures showing the console cable connections between the Switch and the laptop.

Please let me know if you have any queries in this regard.

Thank you again for your patience and understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

Re: 7150 corrupt mount error

mrozone — Fri, 07 Mar 2025 17:59:19 GMT

here you go

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2025.03.07 11:56:20 =~=~=~=~=~=~=~=~=~=~=~=

show version

UNIT 1: compiled on Aug 30 2018 at 04:38:38 labeled as SPS08070c

(25713184 bytes) from Primary

SW: Version 08.0.70cT211

Compressed Boot-Monitor Image size = 786944, Version:10.1.13T225 (mnz10113)

Compiled on Tue Jul 24 10:23:08 2018

HW: Stackable ICX7150-C12-POE

==========================================================================

UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module

Serial #:FEK3811Q08R

Current License: 2X1G

P-ASIC 0: type B160, rev 11 Chip BCM56160_B0

==========================================================================

UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module

==========================================================================

UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module

==========================================================================

1000 MHz ARM processor ARMv7 88 MHz bus

8192 KB boot flash memory

2048 MB code flash memory

1024 MB DRAM

STACKID 1 system uptime is 1 hour(s) 25 minute(s) 59 second(s)

The system started at 00:01:45 GMT+00 Sat Jan 01 2000

The system : started=cold start

ICX7150-C12 Switch#show flash

Stack unit 1:

NAND Type: Micron NAND 2GiB (x 1)

Compressed Pri Code size = 25713184, Version:08.0.70cT211

Compressed Sec Code size = 25713184, Version:08.0.70cT211

Compressed Boot-Monitor Image size = 786944, Version:10.1.13T225

Code Flash Free Space = 1319161856

ICX7150-C12 Switch# shwo ow inf line power

Power Capacity: Total is 124000 mWatts. Current Free is 124000 mWatts.

Power Allocations: Requests Honored 12 times

Port Admin Oper ---Power(mWatts)--- PD Type PD Class Pri Fault/

State State Consumed Allocated Error

--------------------------------------------------------------------------

1/1/1 On Off 0 0 n/a n/a 3 n/a

1/1/2 On Off 0 0 n/a n/a 3 n/a

1/1/3 On Off 0 0 n/a n/a 3 n/a

1/1/4 On Off 0 0 n/a n/a 3 n/a

1/1/5 On Off 0 0 n/a n/a 3 n/a

1/1/6 On Off 0 0 n/a n/a 3 n/a

1/1/7 On Off 0 0 n/a n/a 3 n/a

1/1/8 On Off 0 0 n/a n/a 3 n/a

1/1/9 On Off 0 0 n/a n/a 3 n/a

1/1/10 On Off 0 0 n/a n/a 3 n/a

1/1/11 On Off 0 0 n/a n/a 3 n/a

1/1/12 On Off 0 0 n/a n/a 3 n/a

--------------------------------------------------------------------------

Total 0 0

ICX7150-C12 Switch#show inline power detai

Power Supply Data On unit 1:

++++++++++++++++++

Power Supply Data:

++++++++++++++++++

Power Supply #1:

Max Curr: 2.3 Amps

Voltage: 54.0 Volts

Capacity: 124 Watts

PoePower: 124 Watts

POE Details Info. On Unit 1 :

General PoE Data:

+++++++++++++++++

Firmware

Version

----------------

02.1.0 Build 002

Hardware

Version

----------------

V2R4

Cumulative Port State Data:

+++++++++++++++++++++++++++

#Ports #Ports #Ports #Ports #Ports #Ports #Ports

Admin-On Admin-Off Oper-On Oper-Off Off-Denied Off-No-PD Off-Fault

-------------------------------------------------------------------------

12 0 0 12 0 12 0

Cumulative Port Power Data:

#Ports #Ports #Ports Power Power

Pri: 1 Pri: 2 Pri: 3 Consumption Allocation

-----------------------------------------------

0 0 12 0.000 W 0.000 W

ICX7150-C12 Switch#show interface brief

Port Link State Dupl Speed Trunk Tag Pvid Pri MAC Name

1/1/1 Down None None None None No 1 0 d4c1.9e96.3a84

1/1/2 Down None None None None No 1 0 d4c1.9e96.3a85

1/1/3 Down None None None None No 1 0 d4c1.9e96.3a86

1/1/4 Down None None None None No 1 0 d4c1.9e96.3a87

1/1/5 Down None None None None No 1 0 d4c1.9e96.3a88

1/1/6 Down None None None None No 1 0 d4c1.9e96.3a89

1/1/7 Down None None None None No 1 0 d4c1.9e96.3a8a

1/1/8 Down None None None None No 1 0 d4c1.9e96.3a8b

1/1/9 Down None None None None No 1 0 d4c1.9e96.3a8c

1/1/10 Down None None None None No 1 0 d4c1.9e96.3a8d

1/1/11 Down None None None None No 1 0 d4c1.9e96.3a8e

1/1/12 Down None None None None No 1 0 d4c1.9e96.3a8f

1/2/1 Down None None None None No 1 0 d4c1.9e96.3a91

1/2/2 Down None None None None No 1 0 d4c1.9e96.3a92

1/3/1 Down None None None None No 1 0 d4c1.9e96.3a93

1/3/2 Down None None None None No 1 0 d4c1.9e96.3a94

mgmt1 Down None None None None No None 0 d4c1.9e96.3a84

ICX7150-C12 Switch#

Re: 7150 corrupt mount error

mrozone — Fri, 07 Mar 2025 18:15:45 GMT

ICX7150-C12 Switch#sh run
Current configuration:
!
ver 08.0.70cT211
!
stack unit 1
module 1 icx7150-c12-poe-port-management-module
module 2 icx7150-2-copper-port-2g-module
module 3 icx7150-2-sfp-plus-port-20g-module
!
!
!
!
!
!
!
!
!
!
!
!
!
!
interface ethernet 1/3/1
speed-duplex 1000-full
!
interface ethernet 1/3/2
speed-duplex 1000-full
!
!
!
!
!
!
!
!
!
end

Re: 7150 corrupt mount error

Imran_ruckus — Fri, 07 Mar 2025 19:22:55 GMT

Hi @mrozone

Greetings!!!
Thank you for the response and the update.

I see your Switch version is on an outdated non-UFI version.

We suggest upgrading your Switch to a stable UFI version.

Please refer to the below RUCKUS Lennar Knowledge Base self-help article for the Upgrade process.

https://community.ruckuswireless.com/t5/RUCKUS-Lennar-Support-Knowledge/How-to-upgrade-RUCKUS-ICX-7150-C12P-from-Non-Unified-Forwarding/ta-p/71353

If you can access CLI, We suggest to follow the 2nd option.

Please let me know if you need any help during the upgrade process.

Thank you again for your patience and understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

Re: 7150 corrupt mount error

mrozone — Fri, 07 Mar 2025 22:21:22 GMT

performed the upgrade on the primary but the ethernet port 1/1/1 is not activating when plugged into the modem. I have tested the port on the modem and it does come online when I plug my laptop into it. is there anything special i must do at the cli to force it to get a ip from the modem?

ICX7150-C12 Switch#sh version
Copyright (c) Ruckus Networks, Inc. All rights reserved.
UNIT 1: compiled on May 6 2022 at 23:24:50 labeled as SPS08095g
(31457280 bytes) from Primary SPS08095g.bin (UFI)
SW: Version 08.0.95gT211
Compressed Secondary Boot Code size = 786944, Version:10.1.24T225 (mnz10124)
Compiled on Thu Apr 21 06:08:52 2022

HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module
Serial #:FEK3811Q08R
Software Package: BASE_SOFT_PACKAGE
Current License: 2X1G
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
1000 MHz ARM processor ARMv7 88 MHz bus
8 MB boot flash memory
2 GB code flash memory
1 GB DRAM
STACKID 1 system uptime is 46 second(s)
The system started at 23:25:03 GMT+00 Fri May 06 2022

The system : started=cold start

ICX7150-C12 Switch#show flash
Stack unit 1:
NAND Type: Micron NAND 2GiB (x 1)
Compressed Pri Code size = 31457280, Version:08.0.95gT211 (SPS08095g.bin)
Compressed Sec Code size = 25976488, Version:08.0.80fT211 (SPS08080f.bin)
Compressed Pri Boot Code size = 786944, Version:10.1.14T225 (mnz10114)
Compressed Sec Boot Code size = 786944, Version:10.1.24T225 (mnz10124)
Code Flash Free Space = 1168273408

Re: 7150 corrupt mount error

Imran_ruckus — Mon, 10 Mar 2025 12:39:55 GMT

Hi @mrozone

Greetings!!!
Thank you for the response and the update.

I see your Secondary partition is still on the 08080f version. (Refer to the screenshot below)

Please copy the 08095g version on the secondary and check how it works.

Please enter the below commands to copy the image to the secondary.

Note: Hit Enter to accept each command

enable

copy flash flash secondary

boot system flash secondary yes

Example:

VIDEO LINK AS REFERENCE: https://www.youtube.com/watch?v=Eem1IBgYaWc

ICX7150-24P Router>enable (hit enter to accept the command)
ICX7150-24P Router#copy flash flash secondary (hit enter to accept the command and wait: until the flash finished)
ICX7150-24P Router#boot system flash secondary yes (hit enter to accept the command: the switch will reboot)

If that doesn't work, please share the output of the below commands:

enable

show version

show flash

show inline power

show inline power detail

show interface brief

Please let me know if you have any queries in this regard.

Thank you again for your patience and understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

Re: 7150 corrupt mount error

mrozone — Mon, 10 Mar 2025 17:35:34 GMT

so poe devices (wap's ports 1/1/1 and 1/1/2) are coming online but non-poe devices are not coming online

ICX7150-C12 Switch#show interface br

Port Link State Dupl Speed Trunk Tag Pvid Pri MAC Name
1/1/1 Up Forward Full 1G None No 1 0 d4c1.9e96.3a84
1/1/2 Up Forward Full 1G None No 1 0 d4c1.9e96.3a85
1/1/3 Down None None None None No 1 0 d4c1.9e96.3a86
1/1/4 Up Forward Full 100M None No 1 0 d4c1.9e96.3a87
1/1/5 Down None None None None No 1 0 d4c1.9e96.3a88
1/1/6 Down None None None None No 1 0 d4c1.9e96.3a89
1/1/7 Down None None None None No 1 0 d4c1.9e96.3a8a
1/1/8 Down None None None None No 1 0 d4c1.9e96.3a8b
1/1/9 Down None None None None No 1 0 d4c1.9e96.3a8c
1/1/10 Down None None None None No 1 0 d4c1.9e96.3a8d
1/1/11 Down None None None None No 1 0 d4c1.9e96.3a8e
1/1/12 Down None None None None No 1 0 d4c1.9e96.3a8f
1/2/1 Down None None None None No 1 0 d4c1.9e96.3a91
1/2/2 Down None None None None No 1 0 d4c1.9e96.3a92
1/3/1 Down None None None None No 1 0 d4c1.9e96.3a93
1/3/2 Down None None None None No 1 0 d4c1.9e96.3a94
mgmt1 Down None None None None No None 0 d4c1.9e96.3a84

Re: 7150 corrupt mount error

Imran_ruckus — Mon, 10 Mar 2025 17:49:56 GMT

Hi @mrozone

Please share the output of the below commands as well:

enable

show version

show flash

show inline power

show inline power detail

Thank you.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

Re: 7150 corrupt mount error

mrozone — Mon, 10 Mar 2025 18:05:45 GMT

ICX7150-C12 Switch>sh version
Copyright (c) Ruckus Networks, Inc. All rights reserved.
UNIT 1: compiled on May 6 2022 at 23:24:50 labeled as SPS08095g
(31457280 bytes) from Primary SPS08095g.bin (UFI)
SW: Version 08.0.95gT211
Compressed Primary Boot Code size = 786944, Version:10.1.24T225 (mnz10124)
Compiled on Thu Apr 21 06:08:52 2022

HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module
Serial #:FEK3811Q08R
Software Package: BASE_SOFT_PACKAGE
Current License: 2X1G
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
1000 MHz ARM processor ARMv7 88 MHz bus
8 MB boot flash memory
2 GB code flash memory
1 GB DRAM
STACKID 1 system uptime is 4 minute(s) 50 second(s)
The system started at 01:36:40 GMT+00 Sat May 07 2022

The system : started=warm start reloaded=by "reload"

ICX7150-C12 Switch>show flash
Stack unit 1:
NAND Type: Micron NAND 2GiB (x 1)
Compressed Pri Code size = 31457280, Version:08.0.95gT211 (SPS08095g.bin)
Compressed Sec Code size = 31457280, Version:08.0.95gT211 (SPS08095g.bin)
Compressed Pri Boot Code size = 786944, Version:10.1.24T225 (mnz10124)
Compressed Sec Boot Code size = 786944, Version:10.1.24T225 (mnz10124)
Code Flash Free Space = 1070604288

ICX7150-C12 Switch>show inline power

Power Capacity: Total is 124000 mWatts. Current Free is 124000 mWatts.

Power Allocations: Requests Honored 12 times

Port Admin Oper ---Power(mWatts)--- PD Type PD Class Pri Fault/
State State Consumed Allocated Error
-----------------------------------------------------------------------------
1/1/1 On Off 0 0 n/a n/a 3 n/a
1/1/2 On Off 0 0 n/a n/a 3 n/a
1/1/3 On Off 0 0 n/a n/a 3 n/a
1/1/4 On Off 0 0 n/a n/a 3 n/a
1/1/5 On Off 0 0 n/a n/a 3 n/a
1/1/6 On Off 0 0 n/a n/a 3 n/a
1/1/7 On Off 0 0 n/a n/a 3 n/a
1/1/8 On Off 0 0 n/a n/a 3 n/a
1/1/9 On Off 0 0 n/a n/a 3 n/a
1/1/10 On Off 0 0 n/a n/a 3 n/a
1/1/11 On Off 0 0 n/a n/a 3 n/a
1/1/12 On Off 0 0 n/a n/a 3 n/a
-----------------------------------------------------------------------------
Total 0 0

ICX7150-C12 Switch>show inline power detail

Power Supply Data On unit 1:
++++++++++++++++++

Power Supply Data:
++++++++++++++++++

Power Supply #1:
Max Curr: 2.3 Amps
Voltage: 54.0 Volts
Capacity: 124 Watts
PoePower: 124 Watts

POE Details Info. On Unit 1 :

General PoE Data:
+++++++++++++++++

Firmware
Version
----------------
02.1.8 Build 004

Hardware
Version
----------------
V2R4

Device HW version : 0:V2R4 1:V2R4
Device Temperature(deg-C) : 0:50 1:54
Device Status : 0:Good 1:Good

Cumulative Port State Data:
+++++++++++++++++++++++++++

#Ports #Ports #Ports #Ports #Ports #Ports #Ports
Admin-On Admin-Off Oper-On Oper-Off Off-Denied Off-No-PD Off-Fault
-------------------------------------------------------------------------
12 0 0 12 0 12 0

Cumulative Port Power Data:
+++++++++++++++++++++++++++

#Ports #Ports #Ports Power Power
Pri: 1 Pri: 2 Pri: 3 Consumption Allocation
-----------------------------------------------
0 0 12 0.000 W 0.000 W

ICX7150-C12 Switch#show interface br

Re: 7150 corrupt mount error

Imran_ruckus — Mon, 10 Mar 2025 18:27:54 GMT

Hi @mrozone

Thank you for your prompt response and the update.

Based on the command output, everything appears to be functioning normally.

Could you kindly try disconnecting the Ethernet cables of the non-working devices from their current switch ports and reconnecting them to the same ports or any other available port within the first 12, as indicated in the screenshot below?

Please let me know if that works.

Thank you again for your patience.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

Re: 7150 corrupt mount error

mrozone — Mon, 10 Mar 2025 18:53:58 GMT

I have moved them to a few different ports and still no connectivity.

Re: 7150 corrupt mount error

mrozone — Mon, 10 Mar 2025 18:54:24 GMT

logs dont even indicate its trying to come online

Re: 7150 corrupt mount error

Imran_ruckus — Mon, 10 Mar 2025 19:10:01 GMT

Hi @mrozone

Thank you for the response and the update.

Please enter the below commands and try once again:

Switch>enable
No password has been assigned yet...
Switch#configure terminal
Switch(config)#interface ethernet 1/1/1 to 1/1/12
Switch(config-mif-1/1/1-1/1/12)#no inline power (please wait till the process gets complete)

Switch(config-mif-1/1/1-1/1/12)#inline power (please wait till the process gets complete and check)

Please check and let me know if that works.

If that doesn't work, please share the below information:

1. Please provide a photo showing the status of the lights and the full switch panel with cable connections to the switch ports.

2. How many access points are currently connected to the switch? Please describe the status of the lights on the access points. Similarly, include a photo showing the access points' light status.

Thank you again for your patience and understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

Re: 7150 corrupt mount error

mrozone — Mon, 10 Mar 2025 20:51:04 GMT

Herer you go still no lights on orange cable which goes to modem.