topic Re: How to Reset Lingering, Old SSIDs (Old thread unresponsive) in RUCKUS Support for Lennar Homes

How to Reset Lingering, Old SSIDs (Old thread unresponsive)

Roger_Carvalho — Wed, 27 Dec 2023 19:31:02 GMT

Hello,

Please see prior thread here (https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/How-to-Reset-Lingering-Old-SSIDs/td-p/66681/page/2) which went unanswered, hence I am posting here for further assistance.

The last message I received was from @sanjay_kumar as follows:

"Hi @Roger_Carvalho
Please follow the below instructions:
1. Connect the Laptop to the SSID.
2. Open the browser and enter the APs IP or URL https://unleashed.ruckuswireless.com
3. Enter the credentials of admin users.
4. Go to Admin & Services -> Administration >> Choose Local Upgrade >> Upgrade >> Select the firmware version 200.14.6.1.199 and upgrade.

The complete instructions is there in the below link"

I responded:

"As to item No. 3, to my knowledge, I have never set up any credentials for admin users when the smart home was set up for my household. What should I do?"

My question above is still pending, please advise.

Sincerely,

Re: How to Reset Lingering, Old SSIDs (Old thread unresponsive)

syamantakomer — Thu, 28 Dec 2023 22:03:13 GMT

@sanjay_kumar could you help here.

Re: How to Reset Lingering, Old SSIDs (Old thread unresponsive)

Roger_Carvalho — Thu, 04 Jan 2024 22:29:14 GMT

Hello,

@sanjay_kumar @syamantakomer - Following up on this, again. Please advise.

Sincerely,

Re: How to Reset Lingering, Old SSIDs (Old thread unresponsive)

sanjay_kumar — Fri, 05 Jan 2024 08:24:06 GMT

Hi @Roger_Carvalho
On the step 3, can you try using the either of the below username\password and see if you can login?
admin\sp-admin
super\sp-admin

Re: How to Reset Lingering, Old SSIDs (Old thread unresponsive)

Roger_Carvalho — Fri, 05 Jan 2024 16:18:35 GMT

I have tried both combinations but it did not work. Any ideas?

Sincerely,

Re: How to Reset Lingering, Old SSIDs (Old thread unresponsive)

sanjay_kumar — Mon, 08 Jan 2024 06:45:48 GMT

Hi @Roger_Carvalho

As these APs will be configured by the vendor, I have shared you on a private message with the common passwords which they will set.
If they are not working then you will have to contact the vendor once for the login credentials.

Re: How to Reset Lingering, Old SSIDs (Old thread unresponsive)

Roger_Carvalho — Mon, 08 Jan 2024 20:22:51 GMT

Would you happen to know who that vendor would be? As far as I am concerned, your company would be the vendor for this product. Your system was installed as part of the "smart" home set up for my Lennar home a few years ago and I have had this issue for a long time now without any real solution from your team. Is this forum the only assistance your company provides for these cases? Is this really the only way to reset this device? It looks like a defective device if I cannot reset it by "standard" means.

Re: How to Reset Lingering, Old SSIDs (Old thread unresponsive)

sanjay_kumar — Tue, 09 Jan 2024 02:35:41 GMT

Hi @Roger_Carvalho

We have a dedicated support team for the Lennar home setup, I have asked them to help you in checking the setup and resetting the AP.
They will be reaching out to you on this.

Re: How to Reset Lingering, Old SSIDs (Old thread unresponsive)

Imran_ruckus — Tue, 09 Jan 2024 12:10:02 GMT

Hi @Roger_Carvalho

Greetings!!!

Thank you for contacting RUCKUS Lennar Home Community.

I hope you are doing well!!!

Thank you for the detailed information you shared.

As per the case description, I understand that your RUCKUS R510 Access Points aren’t working.

Please follow the below process to factory reset your APs to configure them with a new SSID.

IMPORTANT NOTE: To perform the factory reset of the Access Points (AP) correctly there must be only ONE AP connected to the RUCKUS ICX-7150-C12P Switch port and others must be unplugged. For Example: If we have 3 APs connected to your Switch ports, we must unplug the 2 APs and keep only ONE AP connected on which we will perform the factory reset. This will act as the Master Access Point. Once we complete the factory reset process with all the configurations and make sure it’s working as expected, we can plug the unplugged APs back into the Switch ports and will sync up with the configurations from the factory reset Master Access Point.

Physical Factory Reset of RUCKUS Access Point:

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/Physical-Factory-Reset-an-Access-Points-Ruckus/td-p/47056

Ruckus Unleashed Set-up using Web:

https://www.youtube.com/watch?v=j8I5aVwMNMg

Password recovery setup: (Highly Recommended)

https://www.youtube.com/watch?v=sqnG8fupaLk

Please let me know if you have any queries in this regard.

Thank you again for your patience and understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.