topic Re: How many IP addreses should i see on my network if i have 2 Ruckus devices in RUCKUS Support for Lennar Homes

How many IP addreses should i see on my network if i have 2 Ruckus devices

Lepresean — Wed, 08 Nov 2023 11:10:09 GMT

Hi There,

I have 2 physical Ruckus devices installed. When i run an IP scan on my home network, it shows me 3 IP address. Is this correct or is there any more information i can give to help answer the question. Many thanks in advance

Re: How many IP addreses should i see on my network if i have 2 Ruckus devices

Sgatjens — Wed, 08 Nov 2023 14:10:43 GMT

Hi @Lepresean

It is correct that you can see 3 IP addresses since one of them belongs to your Ruckus ICX150 switch and the other two are for each of the access points (device in the ceiling)

Kind regards,

Sofia Gätjens

Re: How many IP addreses should i see on my network if i have 2 Ruckus devices

Lepresean — Sun, 12 Nov 2023 04:59:01 GMT

Thanks for your reply. Is it possible to determine which one is the switch as there is nothing in the name that would tell me ?. Also, when i go into my Unleashed app (either the app or via the web browser), it says i have "0" switches ?. Maybe the switch was never setup in the unleashed app ?. Appreciate your help on this

Re: How many IP addreses should i see on my network if i have 2 Ruckus devices

Sgatjens — Mon, 13 Nov 2023 21:21:37 GMT

Hi @Lepresean

You can search for that IP address in the URL bar of your Web browser:

If the IP leads you to the Unleashed GUI, it corresponds to your access points. However, if it directs you to the following, it corresponds to your switch ICX.

Concerning the switch tab in your Unleashed app/GUI, the switch isn't automatically added. You need to follow specific steps to include it there.

Please follow the below steps to get Switch in sync with Unleashed. We will delete the Switch from Unleased and Add it back.

Steps to synchronize the Switch (ICX-7150-C12P) to the unleashed Access Points:

Switch side:

Confirm that the switch is running FastIron firmware version 08.0.90 or later using the following command:
ICX7150-C12-Switch#show version

Make sure that the SSH server is enabled:
1. device>enable
device# configure terminal
device# show ip ssh config

If it is disabled, please run the following command:

device(config)# crypto key generate
device(config)# write memory

Check again with the command " show ip ssh config" to confirm that the SSH server was enabled correctly.

On the Unleashed dashboard:

1. Make sure the management approval is enabled.

https://docs.commscope.com/bundle/unleashed-200.9-onlinehelp/page/GUID-A887C55E-6973-4496-9413-302E8..

2- Remove the existing Switch from the Unleashed (Please refer to the below picture):

3. Hit Add on that dashboard

4-Put the IP address of the ICX switch (ICX-7150-C12P) and Password

In your case, will be the one showing up on the Switch tap:

(you can also confirm the IP address from the switch's CLI with the following command:

Device>enable
Device#show ip address

5-Username and password for Switch authentication are the same as what you use to log in for Switch on Web or CLI (Putty).

https://docs.commscope.com/bundle/unleashed-200.9-onlinehelp/page/GUID-30C6694A-6AEE-4DF8-9459-1AB18...

To sync the data, it will take us a while, so after a couple of minutes, it should say connected.

Once the Switch gets synchronized, please check the dashboard again.

Please let me know if you have any queries in this regard.

Kind regards,

Sofia Gätjens

Re: How many IP addreses should i see on my network if i have 2 Ruckus devices

Lepresean — Sat, 18 Nov 2023 17:15:35 GMT

Hi Sofia, thanks so much and apologies for the delay in replying. I managed to get the login screen of the switch, however i do not know the login. Can you help me with reseting or something ?

Re: How many IP addreses should i see on my network if i have 2 Ruckus devices

Sgatjens — Mon, 20 Nov 2023 12:18:15 GMT

Hello @Lepresean

Please check the following link:

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/Admin-usernames-and-passwords-for-the-Ruckus-Wi-Fi-Access-Points/td-p/46740

Note: Initially attempt to log in using the credentials "super/sp-admin." If unsuccessful, proceed with the ones located within the green square.

Kind regards,

Sofia Gätjens

Re: How many IP addreses should i see on my network if i have 2 Ruckus devices

Lepresean — Sun, 11 Feb 2024 21:50:40 GMT

Hi Sofia,

Unfortunately none of these worked. Is is worth me persuing this as i am not sure if there are many advantatages of being able to see my switch in the unleased app ?. Thanks

Re: How many IP addreses should i see on my network if i have 2 Ruckus devices

Sgatjens — Tue, 13 Feb 2024 14:29:33 GMT

Hi @Lepresean

When the ICX is connected to your Unleashed GUI, you gain visibility into port usage, status, traffic statistics, errors, connected clients, model, firmware version, and the ability to back up the current configuration. As a Lennar customer, the capabilities on your ICX are somewhat limited due to its straightforward configuration. Additionally, the status of clients and traffic can also be viewed on the APs tab. Therefore, managing the switch is relatively basic.

Kind regards,

Sofia Gätjens