topic Re: R510 access point doesn't turn on after power failure. Reset doesn't work in RUCKUS Support for Lennar Homes

R510 access point doesn't turn on after power failure. Reset doesn't work

Karthick — Wed, 30 Aug 2023 22:51:00 GMT

R510 access point doesn't turn on after power failure. Reset doesn't work. How to make the access point work again?

Re: R510 access point doesn't turn on after power failure. Reset doesn't work

Imran_ruckus — Wed, 30 Aug 2023 23:38:33 GMT

Hi @Karthick

Greetings!!!

Thank you for contacting RUCKUS Lennar Home Community.

Hope you are doing well!!!

Thank you for the information you shared.

As per the case description, I understand that your RUCKUS setup is not working, and Access Points do not have power after a power outage.

Could you please let us know the answers to the below queries to assist you better?

1. On your switch while it's plugged into the outlet, do you see any lights on? (Amber or green) Please let us know which lights are on. (Please refer to the below picture and share a picture of the same, showing the light status and the FULL Switch panel cable connections to the Switch ports)

2. May I know how many Access Points are connected to the Switch?

Please help us with pictures of your ICX-7150-C12P Switch showing the status of the lights and cable connections to the Switch ports.

Before uploading the photos please log in to the RUCKUS account and you can upload the image.

Please let us know the answers to ALL the above queries or let us know if you have any queries in this regard.

Thank you again for your patience.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

Re: R510 access point doesn't turn on after power failure. Reset doesn't work

Karthick — Sat, 02 Sep 2023 18:12:03 GMT

1. Port that has an access point connected have lights off

2. There are three, and all are down with no lights. When I tried resetting, I disconnected all of them and just had one.

3. All the lights in the access point are down.

Re: R510 access point doesn't turn on after power failure. Reset doesn't work

Imran_ruckus — Mon, 04 Sep 2023 15:12:47 GMT

Hi @Karthick

Greetings!!!

Thank you for the response and the update.

As per the light status of your RUCKUS ICX-7150-C12P Switch, it seems normal.

We may have to check the ports and some other information of the Switch from the CLI access.

Please follow the below steps to access CLI and get the output of the below-mentioned commands.

Please follow the below steps and help us with the queries,

1. To check this issue, we must identify the ‘current’ IP address assigned by your local router to the switch ICX-7150-C12P

I will leave you a guide on how to perform an IP scanner on your local network to identify the switch IP address very easily.

How to find my Ruckus “Devices IP address” using free applications:

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-find-my-Ruckus-Devices-IP-address-using-free-applications/td-p/47027

2. Once we identify the IP address of the switch proceed to access remotely to the device “Command Line”

How to remotely access to 'ICX 7150-C12P' or 'access points' "Network devices":

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-remotely-access-to-ICX-7150-12P-or-access-points-quot/td-p/47388

If you can access the Command line should look like this:

ICX7150-C12 Router> OR

ICX7150-C12 Switch>

Please enter the below commands once you log in to CLI and share the output.

Note: Hit Enter to accept each command

enable

show version

show flash

show inline power
show interface brief

Please share the output of the above commands or share the screenshots if stuck at any step or error (if any) and let me know if you have any queries in this regard.

Thank you again for your patience and understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.