topic Re: new r700 disconnected in ZD5100 after upgrading in Community and Online Support Services

new r700 disconnected in ZD5100 after upgrading

ian_calisnao — Tue, 12 Jan 2016 01:37:26 GMT

Hello

We recently purchased a r700. Currently we have a ZD5100 and 48 r7982 AP's.
When I plug the r700 it says upgrading firmware and reboot afterwards.

When it turns on DIR is only blinking and in the ZD it says disconnected but have an IP.

we are currently using 9.8.2.0.15 software.

Should we upgrade?

Re: new r700 disconnected in ZD5100 after upgrading

andrea_coppini — Tue, 12 Jan 2016 07:06:13 GMT

Yes you will need to upgrade the ZD. The R710 didn't exist when 9.8.2 was released.

Re: new r700 disconnected in ZD5100 after upgrading

ian_calisnao — Tue, 12 Jan 2016 07:45:46 GMT

Can I directly upgrade to the latest v9.9.1?

Thank you.

Re: new r700 disconnected in ZD5100 after upgrading

andrea_coppini — Tue, 12 Jan 2016 08:32:42 GMT

Latest is 9.12. Read the release notes for upgrade process and for AP support.

Re: new r700 disconnected in ZD5100 after upgrading

seanmuir — Tue, 19 Jan 2016 09:17:17 GMT

This question is in relationship to a the r700 which is support all the way down to 9.8 GA.

It may be down to the AP's being in a remote location

Provisioning loops can be caused by one of the 2 following issues:

1. MTU

Solution:

Set the LWAPP MTU to 1250

2. QoS settings on ZD

ruckus> en
ruckus# config
You have all rights in this mode.
ruckus(config)# system
ruckus(config-sys)# qos
ruckus(config-sys-qos)# show
System QoS:
ToS DATA TUNNEL = 0xA0
ToS CTRL TUNNEL = 0xA0
ToS Classification-Voice = 0xE0 0xC0 0xB8
ToS Classification-Video = 0xA0 0x80
ToS Classification-Data = 0x0
ToS Classification-Background = 0x0
Tx fail threshold = 50
heuristics inter-packet-gap Video = 0  65
heuristicsinter-packet-gap Voice = 15 275
heuristics packet-length Video = 1000  1518
heuristics packet-length Voice = 70 400
heuristics classification Video = 50000
heuristics classification Voice = 600
heuristics no classification Video = 500000
heuristics no classification Voice = 10000

Solution:

The values highlighted need to be set are per the below:

ToS DATA TUNNEL = 0x00
ToS CTRL TUNNEL = 0x00

This can be done using this command:

ruckus# set_qos sys tunnel-tos-val data 0x00

and

ruckus# set_qos sys tunnel-tos-val ctrl 0x00

It is mainly caused when 3rd party switches can have traffic marked differently and prevent the AP from taking their config.

Re: new r700 disconnected in ZD5100 after upgrading

seanmuir — Tue, 19 Jan 2016 09:17:34 GMT

You don't need to upgrade, see comment above

🙂

Re: new r700 disconnected in ZD5100 after upgrading

seanmuir — Wed, 20 Jan 2016 23:03:04 GMT

I would hold out on upgrading to 9.12 MR 2 see John's comments on ZD management lock up:

https://forums.ruckuswireless.com/ruckuswireless/topics/any-update-on-when-9-12-mr2-will-be-availabl...

Re: new r700 disconnected in ZD5100 after upgrading

ian_calisnao — Mon, 25 Jan 2016 01:05:49 GMT

Hi where can I set LWAPP MTU to 1250?

Re: new r700 disconnected in ZD5100 after upgrading

ian_calisnao — Thu, 04 Feb 2016 05:51:10 GMT

Still cant connect my r700, after upgrading of firmware, the DIR is only blinking. I also cannot ping the AP, someone say that one of our switch is dropping a packet form the AP. It is advisable to upgrade to 9.9.x?