https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/r650-installation-help-please/m-p/33530#M9404 <P style="margin: 0;">Hi,</P> <P style="margin: 0;"></P> <P style="margin: 0;">Follow below steps:</P> <OL> <LI>Power up the AP, push the reset button and hold it for 12 seconds. This will default the AP to factory mode.</LI> <LI>Now connect this AP to network port (In your case, firewall) and let it get an IP address over untagged VLAN (by default AP will talk over untagged frames).</LI> <LI>Make sure this AP cannot reach the existing controller IP (if it is managed by a controller at present).</LI> <LI>Once it gets the IP, access the AP (username: super || password: sp-admin) and the flash it to Unleashed version. Download image can be found <A href="https://support.ruckuswireless.com/software_downloads/3137-ruckus-unleashed-ap-200-10-10-5-246-ga-refresh1-software-for-r650" target="_blank" rel="noopener noopener noreferrer">here</A></LI> <LI>Post flashing the AP with Unleashed image, configure it as per your requirements.</LI> </OL> Mon, 13 Sep 2021 20:57:03 GMT syamantakomer 2021-09-13T20:57:03Z https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/r650-installation-help-please/m-p/33529#M9403 <P style="margin: 0;">I have a non R650 unleashead.<BR />1- How can I pull this device from hotzone mode to unleashead mode?<BR />&nbsp; 2- I also want this device to get ip from the firewall connected on the switch. How can i get ip from dhcp in firewall. Could you please help which ports will be tagged or untagged?</P> Wed, 25 Aug 2021 13:08:03 GMT https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/r650-installation-help-please/m-p/33529#M9403 emre_unsal 2021-08-25T13:08:03Z https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/r650-installation-help-please/m-p/33530#M9404 <P style="margin: 0;">Hi,</P> <P style="margin: 0;"></P> <P style="margin: 0;">Follow below steps:</P> <OL> <LI>Power up the AP, push the reset button and hold it for 12 seconds. This will default the AP to factory mode.</LI> <LI>Now connect this AP to network port (In your case, firewall) and let it get an IP address over untagged VLAN (by default AP will talk over untagged frames).</LI> <LI>Make sure this AP cannot reach the existing controller IP (if it is managed by a controller at present).</LI> <LI>Once it gets the IP, access the AP (username: super || password: sp-admin) and the flash it to Unleashed version. Download image can be found <A href="https://support.ruckuswireless.com/software_downloads/3137-ruckus-unleashed-ap-200-10-10-5-246-ga-refresh1-software-for-r650" target="_blank" rel="noopener noopener noreferrer">here</A></LI> <LI>Post flashing the AP with Unleashed image, configure it as per your requirements.</LI> </OL> Mon, 13 Sep 2021 20:57:03 GMT https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/r650-installation-help-please/m-p/33530#M9404 syamantakomer 2021-09-13T20:57:03Z