topic Re: add T300 AP that is running 100.x code to the existing SZ 100 Controller in Access Points - Indoor and Outdoor https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/add-T300-AP-that-is-running-100-x-code-to-the-existing-SZ-100/m-p/32412#M9074 set scg ip&nbsp;command is available in AP104.x.<BR />Upgrade AP to 104.x to issue this command. Fri, 09 Feb 2018 07:48:27 GMT karthik 2018-02-09T07:48:27Z add T300 AP that is running 100.x code to the existing SZ 100 Controller https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/add-T300-AP-that-is-running-100-x-code-to-the-existing-SZ-100/m-p/32411#M9073 How do i add T300 AP that is running 100.x code to the existing SZ 100 Controller because it is not recognizing the "set scg ip " command? Fri, 09 Feb 2018 07:07:56 GMT https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/add-T300-AP-that-is-running-100-x-code-to-the-existing-SZ-100/m-p/32411#M9073 lefhoko_radisak 2018-02-09T07:07:56Z Re: add T300 AP that is running 100.x code to the existing SZ 100 Controller https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/add-T300-AP-that-is-running-100-x-code-to-the-existing-SZ-100/m-p/32412#M9074 set scg ip&nbsp;command is available in AP104.x.<BR />Upgrade AP to 104.x to issue this command. Fri, 09 Feb 2018 07:48:27 GMT https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/add-T300-AP-that-is-running-100-x-code-to-the-existing-SZ-100/m-p/32412#M9074 karthik 2018-02-09T07:48:27Z Re: add T300 AP that is running 100.x code to the existing SZ 100 Controller https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/add-T300-AP-that-is-running-100-x-code-to-the-existing-SZ-100/m-p/32413#M9075 What happens when i restore to factory settings an AP that was upgraded from 100.x to 104.x, does it go back to 100.x or will remain 104.x? Fri, 09 Feb 2018 08:10:55 GMT https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/add-T300-AP-that-is-running-100-x-code-to-the-existing-SZ-100/m-p/32413#M9075 lefhoko_radisak 2018-02-09T08:10:55Z Re: add T300 AP that is running 100.x code to the existing SZ 100 Controller https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/add-T300-AP-that-is-running-100-x-code-to-the-existing-SZ-100/m-p/32414#M9076 it remains 104. Fri, 09 Feb 2018 12:04:28 GMT https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/add-T300-AP-that-is-running-100-x-code-to-the-existing-SZ-100/m-p/32414#M9076 hyosang_choi 2018-02-09T12:04:28Z