https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/7372-E-configuration-Indoor-multi-rooms-feeder-splitter-omni/m-p/27978#M7871 Hi,<BR /><BR />I'd like to deploy 7372-E equipments with feeder lines and omni antenna in a small building where large wall (50cm concrete) and fire proof doors are present.<BR /><BR />My idea was to bring feeders from AP to the rooms by putting some power splitter (3 ways) and bring 6 omni antennas in the 6 rooms.<BR />The rooms are rather small &lt;30 square meters max and the purpose of this wifi is coverage for 1 or 2 mobile connection.<BR />I need to respect the EIRP indoor in 2.4Ghz and 5.4Ghz (based on the cable/splitter loss and antenna Gain 2.4G=100mw and 5.4G=500mw)<BR /><BR />1rst question:<BR /><BR />Can i configure different ext antenna gain on ANT 1 and ANT2 in both 2.4GHZ and 5.4GHZ ?<BR /><BR /><BR />2nd question:<BR /><BR />Isolation between antenna will be greater then 30dB, must i deactivate MIMO, are shall i leave the AP deal with this isolation between ANT1 and ANT2?<BR /><BR />3nd question:<BR /><BR />If i need a small outdoor coverage in front of this building, can i use one of the splitted RF acces of the AP to install to install a panel antenna.<BR /><BR />I'm conscience that the small gain of the bi-band omni 5/7dBi antennas, and the feeder loss will reduce my coverage zone.<BR /><BR />Hope i'm clear enough, thanks by advance for the help! Fri, 24 Jul 2015 12:27:43 GMT lefebvre_christ 2015-07-24T12:27:43Z https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/7372-E-configuration-Indoor-multi-rooms-feeder-splitter-omni/m-p/27977#M7870 Like to have advices on CLI configuration for 7372-E indoor installation with multi rooms power splitter (large band 2.4/5.4Ghz) and omni antennas Fri, 24 Jul 2015 12:04:42 GMT https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/7372-E-configuration-Indoor-multi-rooms-feeder-splitter-omni/m-p/27977#M7870 lefebvre_christ 2015-07-24T12:04:42Z https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/7372-E-configuration-Indoor-multi-rooms-feeder-splitter-omni/m-p/27978#M7871 Hi,<BR /><BR />I'd like to deploy 7372-E equipments with feeder lines and omni antenna in a small building where large wall (50cm concrete) and fire proof doors are present.<BR /><BR />My idea was to bring feeders from AP to the rooms by putting some power splitter (3 ways) and bring 6 omni antennas in the 6 rooms.<BR />The rooms are rather small &lt;30 square meters max and the purpose of this wifi is coverage for 1 or 2 mobile connection.<BR />I need to respect the EIRP indoor in 2.4Ghz and 5.4Ghz (based on the cable/splitter loss and antenna Gain 2.4G=100mw and 5.4G=500mw)<BR /><BR />1rst question:<BR /><BR />Can i configure different ext antenna gain on ANT 1 and ANT2 in both 2.4GHZ and 5.4GHZ ?<BR /><BR /><BR />2nd question:<BR /><BR />Isolation between antenna will be greater then 30dB, must i deactivate MIMO, are shall i leave the AP deal with this isolation between ANT1 and ANT2?<BR /><BR />3nd question:<BR /><BR />If i need a small outdoor coverage in front of this building, can i use one of the splitted RF acces of the AP to install to install a panel antenna.<BR /><BR />I'm conscience that the small gain of the bi-band omni 5/7dBi antennas, and the feeder loss will reduce my coverage zone.<BR /><BR />Hope i'm clear enough, thanks by advance for the help! Fri, 24 Jul 2015 12:27:43 GMT https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/7372-E-configuration-Indoor-multi-rooms-feeder-splitter-omni/m-p/27978#M7871 lefebvre_christ 2015-07-24T12:27:43Z