https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/Unleashed-dashboard-fails-to-connect-intermitenly/m-p/23970#M6567 I have upgraded to the Ruckus Unleashed wireless using zoneflex R510's from Cisco Aironet 1200 AG's. I still have about 5 of the cisco AP's online with 3 R510 hooked up.&nbsp;<BR /><BR />I have 1 R510 that keeps showing "disconnected" status in the dashboard when I can get into it. I have replaced it already and checked port settings on the switch its plugged into and everything seems ok. But when I try to check the dashboard it will connect and then I wont be able to click anything and when I refresh it says "connection refused".&nbsp;<BR /><BR />The R510 disconnecting is not the master and I have to reload the page 5-10 times before I can actually get the dashboard back up. and even then after a minute or 2 the dashboard freezes again and says connection refused. Every once in a while when connecting it will also say "rebuilding wireless".<BR /><BR />Does anyone have an idea of where I should look? I do not have a physical onsite firewall and all connections are managed through the windows firewall in server 2008R2. I have a wireless controller that manage the cisco AP's.<BR /><BR />&nbsp;I just dont know why it keeps doing this. It makes the wireless very slow and unreliable and i have a PC showing data on a screen outside my office that uses wireless, it is constantly dropping signal and unable to reconnect without me manually renabling the wireless.&nbsp; Fri, 13 Oct 2017 16:43:06 GMT samuel_reyes_ch 2017-10-13T16:43:06Z https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/Unleashed-dashboard-fails-to-connect-intermitenly/m-p/23970#M6567 I have upgraded to the Ruckus Unleashed wireless using zoneflex R510's from Cisco Aironet 1200 AG's. I still have about 5 of the cisco AP's online with 3 R510 hooked up.&nbsp;<BR /><BR />I have 1 R510 that keeps showing "disconnected" status in the dashboard when I can get into it. I have replaced it already and checked port settings on the switch its plugged into and everything seems ok. But when I try to check the dashboard it will connect and then I wont be able to click anything and when I refresh it says "connection refused".&nbsp;<BR /><BR />The R510 disconnecting is not the master and I have to reload the page 5-10 times before I can actually get the dashboard back up. and even then after a minute or 2 the dashboard freezes again and says connection refused. Every once in a while when connecting it will also say "rebuilding wireless".<BR /><BR />Does anyone have an idea of where I should look? I do not have a physical onsite firewall and all connections are managed through the windows firewall in server 2008R2. I have a wireless controller that manage the cisco AP's.<BR /><BR />&nbsp;I just dont know why it keeps doing this. It makes the wireless very slow and unreliable and i have a PC showing data on a screen outside my office that uses wireless, it is constantly dropping signal and unable to reconnect without me manually renabling the wireless.&nbsp; Fri, 13 Oct 2017 16:43:06 GMT https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/Unleashed-dashboard-fails-to-connect-intermitenly/m-p/23970#M6567 samuel_reyes_ch 2017-10-13T16:43:06Z https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/Unleashed-dashboard-fails-to-connect-intermitenly/m-p/23971#M6568 I have the same issue with a network with R600 an R310, the dashboard fails, it logs me out of the session and when I finally get in to check it appears almost all of the APs disconnected but they are working.<BR /><BR />&nbsp;Ruckus support told me to change my static IP configuration to DHCP, which is weird because in Wise preparation they told to use Static IPs. Fri, 13 Oct 2017 21:05:30 GMT https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/Unleashed-dashboard-fails-to-connect-intermitenly/m-p/23971#M6568 roberto_constan 2017-10-13T21:05:30Z