https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/Downgrading-firmware-on-ZD1200-from-10-1-0-0-to-9-xx/m-p/20728#M5515 <P style="margin: 0;">I just bought a new ZD1200 and i would like to install 9.xxxx on it so i can use my zone flex 7363 with this unit.</P> <P style="margin: 0;">My problem is that it comes by default with 10.1.0.0 build 1515. I have tried to make a factory reset via the browser interface and via holding down the F/D button on the hardware for about 15 seconds and it still shows up the 10.1.0.0 firmware.</P> <P style="margin: 0;"></P> <P style="margin: 0;">How do i downgrade the firmware??&nbsp;</P> Mon, 11 Jan 2021 13:09:39 GMT rasmus_hecter 2021-01-11T13:09:39Z https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/Downgrading-firmware-on-ZD1200-from-10-1-0-0-to-9-xx/m-p/20728#M5515 <P style="margin: 0;">I just bought a new ZD1200 and i would like to install 9.xxxx on it so i can use my zone flex 7363 with this unit.</P> <P style="margin: 0;">My problem is that it comes by default with 10.1.0.0 build 1515. I have tried to make a factory reset via the browser interface and via holding down the F/D button on the hardware for about 15 seconds and it still shows up the 10.1.0.0 firmware.</P> <P style="margin: 0;"></P> <P style="margin: 0;">How do i downgrade the firmware??&nbsp;</P> Mon, 11 Jan 2021 13:09:39 GMT https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/Downgrading-firmware-on-ZD1200-from-10-1-0-0-to-9-xx/m-p/20728#M5515 rasmus_hecter 2021-01-11T13:09:39Z https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/Downgrading-firmware-on-ZD1200-from-10-1-0-0-to-9-xx/m-p/20729#M5516 <P style="margin: 0;">It's been some time, but you should be able to get a copy of the firmware from Ruckus support and then follow a downgrade path.&nbsp; I don't know if 10.x down to 9.x versions causes any issues though.</P> <P style="margin: 0;"></P> <P style="margin: 0;">support.ruckuswireless.com - check there for the ZD1200 firmware version you want.</P> Mon, 11 Jan 2021 14:59:01 GMT https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/Downgrading-firmware-on-ZD1200-from-10-1-0-0-to-9-xx/m-p/20729#M5516 karl_lavender_ 2021-01-11T14:59:01Z https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/Downgrading-firmware-on-ZD1200-from-10-1-0-0-to-9-xx/m-p/20730#M5517 <P style="margin: 0;">Hi karl and thanx for the reply.</P> <P style="margin: 0;">I allready have the firmware 9.12.3.0.154. and it should be possible to upgrade the ZD 1200 if the firmware is below the factory default.</P> <P style="margin: 0;">i have tried to uploading via the "Restore" button in the GUI and it just loads and loads......maybe i should give it more time (i gave it around 15 minutes).</P> <P style="margin: 0;">So the real question is - is it doable to downgrade firmware, when the factory default is higher than the firmware i try to install.</P> Mon, 11 Jan 2021 15:08:39 GMT https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/Downgrading-firmware-on-ZD1200-from-10-1-0-0-to-9-xx/m-p/20730#M5517 rasmus_hecter 2021-01-11T15:08:39Z https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/Downgrading-firmware-on-ZD1200-from-10-1-0-0-to-9-xx/m-p/20731#M5518 <P style="margin: 0;">Hi Rasmus,</P> <P style="margin: 0;"></P> <P style="margin: 0;"><SPAN>9.12.3.0.154 is the last version&nbsp;which supports 7363.</SPAN></P> <P style="margin: 0;"></P> <P style="margin: 0;"><A href="https://support.ruckuswireless.com/software_terms_and_conditions/2484-zd1200-9-12-3-0-154-mr3-refresh9-software-release" target="_blank" rel="noopener">https://support.ruckuswireless.com/software_terms_and_conditions/2484-zd1200-9-12-3-0-154-mr3-refresh9-software-release</A></P> <P style="margin: 0;"></P> <P style="margin: 0;">Downgrading directly from 10.x to 9.12 will factory reset the ZD and you have to reconfigure it.</P> <P style="margin: 0;"></P> <P style="margin: 0;">Factory resetting the ZD will not downgrade the firmware, you have to downgrade it manually from GUI or ZD CLI.</P> Mon, 11 Jan 2021 19:34:34 GMT https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/Downgrading-firmware-on-ZD1200-from-10-1-0-0-to-9-xx/m-p/20731#M5518 syamantakomer 2021-01-11T19:34:34Z