topic Re: P300 Communication Status in SCADA in Access Points - Indoor and Outdoor

P300 Communication Status in SCADA

vaitheeswaran_e — Mon, 06 Jan 2020 10:46:19 GMT

I am using P300 Root and Non-Root bridges. I need to take the communication status and the signal strength in the SCADA(Wonderware Intouch) without logging in the browser. Please suggest an solution for this!!!!!!!!

Re: P300 Communication Status in SCADA

syamantakomer — Mon, 06 Jan 2020 13:17:49 GMT

Hi Vaitheeswaran,

If your SCADA system supports SNMP integration then you can use it to pull the stats from P300.

Here is the link for P300 MIB file which you have to add in your server and setup SNMP.

https://support.ruckuswireless.com/software_downloads/983-zoneflex-p300-ptmtp-ap-bridge-mibs-for-version-100-1-0-9-43-ga-software-release

Make sure that you enable SNMP on P300 bridge as well.

Regards,
Syamantak Omer

Re: P300 Communication Status in SCADA

sanjay_kumar — Tue, 07 Jan 2020 02:17:55 GMT

Hi Vaitheeswaran,

If you want to use SNMP, try with the below OIDs.

WLINK RSSI : .1.3.6.1.4.1.25053.1.1.15.1.1.1.1.1.11
WLINK Uptime : .1.3.6.1.4.1.25053.1.1.15.1.1.1.1.1.10
WLINK Role : .1.3.6.1.4.1.25053.1.1.15.1.1.1.1.1.2

Re: P300 Communication Status in SCADA

vaitheeswaran_e — Sat, 11 Jan 2020 05:53:43 GMT

Hello Syamantak,

I am using Wonderware Intouch Software as SCADA. It supports SNMP Integration, Please check the below link it's for configurating the Bridges with Wonderware using System Management Console. I need to take the Connection Status( Whether the bridges are connected or not) and Signal Strength of the Bridge as a graphical representation. Please guide me how to take the datatype for the Connection Status and Signal Strength.

https://www.logic-control.com/datasheets/1/Device%20Connectivity/OI%20Servers/SNMP%20OI%20Server%20User%20Guide.pdf

Re: P300 Communication Status in SCADA

syamantakomer — Mon, 13 Jan 2020 12:53:34 GMT

Hi Vaitheeswaran,

As suggested by Sanjay in his previous comment, please use below SNMP OIDs to pull the required details.

WLINK RSSI (Signal Strength) : .1.3.6.1.4.1.25053.1.1.15.1.1.1.1.1.11
WLINK Uptime (Connection status): .1.3.6.1.4.1.25053.1.1.15.1.1.1.1.1.10
WLINK Role : .1.3.6.1.4.1.25053.1.1.15.1.1.1.1.1.2

Let us know if that answers your query or you have any further queries.

Regards,
Syamantak Omer

Re: P300 Communication Status in SCADA

vaitheeswaran_e — Wed, 22 Jan 2020 13:09:14 GMT

Hi Syamantak,

Is there any User Interface Protocol for Ruckus P300, so that i could access the signal status and strength by calling through the datatypes in my SCADA.

Thanks and Regards,
Vaitheeswaran Elango.

Re: P300 Communication Status in SCADA

syamantakomer — Wed, 22 Jan 2020 14:45:44 GMT

Hi Vaitheeswaran,

I think you have already asked this on a different forum post and my colleagues Michael Brado already answered it.

https://forums.ruckuswireless.com/ruckuswireless/topics/p300

There is no HMI interface available in P300, all you can do is pull the SNMP data by setting up SNMP server on your SCADA (if supported) and configure the server details in P300. Rest data processing for graphical representation needs to be done on server side.

Regards,
Syamantak Omer