https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/Login-AP-WebUI-from-controller/m-p/14164#M3532 Hi Irvan,<BR /><BR />When AP connects to SZ/vSZ, AP's web interface would be disabled. It is disabled, to save its memory; below is the output from AP's CLI.<BR /><PRE>Please login: admin<BR />password :<BR />Copyright(C) 2016 Ruckus Wireless, Inc. All Rights Reserved.<BR />** Ruckus R710 Multimedia Hotzone Wireless AP: 351603804913<BR />rkscli: get https<BR />HTTPs access is enabled<BR />But the service is off, it is turned off to save memory once AP is managed by SCG!<BR />If you need the service, please enable again by command "set https/http enable"!<BR />OK<BR />rkscli:</PRE>If you want to enable it please run "set https", but it is strongly recommended not to enable it.<BR /><BR />Regards,<BR />Abilash PR. Tue, 18 Jul 2017 14:21:57 GMT abilash_p_r 2017-07-18T14:21:57Z https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/Login-AP-WebUI-from-controller/m-p/14163#M3531 Hi, there is possible to open AP WebUI from controller Smartzone100 ? i already try connect to ip AP, but the AP WebUI cannot open. Tue, 18 Jul 2017 03:26:47 GMT https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/Login-AP-WebUI-from-controller/m-p/14163#M3531 irvan_irvan_64v 2017-07-18T03:26:47Z https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/Login-AP-WebUI-from-controller/m-p/14164#M3532 Hi Irvan,<BR /><BR />When AP connects to SZ/vSZ, AP's web interface would be disabled. It is disabled, to save its memory; below is the output from AP's CLI.<BR /><PRE>Please login: admin<BR />password :<BR />Copyright(C) 2016 Ruckus Wireless, Inc. All Rights Reserved.<BR />** Ruckus R710 Multimedia Hotzone Wireless AP: 351603804913<BR />rkscli: get https<BR />HTTPs access is enabled<BR />But the service is off, it is turned off to save memory once AP is managed by SCG!<BR />If you need the service, please enable again by command "set https/http enable"!<BR />OK<BR />rkscli:</PRE>If you want to enable it please run "set https", but it is strongly recommended not to enable it.<BR /><BR />Regards,<BR />Abilash PR. Tue, 18 Jul 2017 14:21:57 GMT https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/Login-AP-WebUI-from-controller/m-p/14164#M3532 abilash_p_r 2017-07-18T14:21:57Z https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/Login-AP-WebUI-from-controller/m-p/14165#M3533 Hi Abilash, ok i understand. Thanks for your support <span class="lia-unicode-emoji" title=":slightly_smiling_face:">🙂</span> Thu, 20 Jul 2017 01:53:16 GMT https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/Login-AP-WebUI-from-controller/m-p/14165#M3533 irvan_irvan_64v 2017-07-20T01:53:16Z