How to configure eth0 on R550?

iwx — Mon, 06 Jul 2026 14:50:10 GMT

Dear all,

according to older docs and threads, the second port (eth0) on a R550 can be precisely configured. However, they all refer to older releases and I do not find it anywhere, neither by CLI. Can someone point me into the right direction or has this feature been removed in the latest release?

Device: R550
System Version: 200.19.7.11.283
Powered by PoE on eth1

eth1 is a trunk with two VLANs (default and a tagged one) and I want to pass the tagged one as untagged on eth0.

Thank you and kind regards,

David.

Re: How to configure eth0 on R550?

cmak — Tue, 07 Jul 2026 07:48:43 GMT

Your firmware is Unleashed.
You may login the AP and set it by CLI

command:
get eth
set eth

Re: How to configure eth0 on R550?

iwx — Tue, 07 Jul 2026 08:45:19 GMT

Thanks, cmak.

That's the point - I do not have this commands available. When I log in, I have (entering enable -> config -> system -> interface):

Welcome to Ruckus Unleashed Network Command Line Interface ruckus> help Commands available: exit Ends the CLI session. help Shows available commands. quit Ends the CLI session. history Shows a list of previously run commands. enable <force> Enables privileged commands. Using option "force" to force disconnect previous session. ping <IP-ADDR/DOMAIN-NAME> Sends ICMP echo packets to an IP/IPv6 address or domain name. ping <IP-ADDR/DOMAIN-NAME> -s <NUMBER> Sends ICMP echo packets to an IP/IPv6 address or domain name with -s option to set the size of packet. ruckus> enable ruckus# help Commands available: exit Ends the CLI session. help Shows available commands. quit Ends the CLI session. history Shows a list of previously run commands. : config Configures options and settings. : ap-mode Go to local AP's CLI from Master's CLI. ruckus# config You have all rights in this mode. ruckus(config)# help Commands available: help Shows available commands. history Shows a list of previously run commands. no location-services <WORD> Deletes an location server from the list of location servers. : reportd Configures Reportd settings. Enter ruckus(config-reportd)# ruckus(config)# system ruckus(config-sys)# help Commands available: help Shows available commands. history Shows a list of previously run commands. : interface Configures IP address and VLAN settings. : generate-token Re-generate unleashed-network unique token. ruckus(config-sys)# interface ruckus(config-sys-if)# help Commands available: help Shows available commands. history Shows a list of previously run commands. abort Exits the config-syst-if context without saving changes. end Saves changes, and then exits config-syst-if context. exit Saves changes, and then exits config-syst-if context. quit Exits the config-syst-if context without saving changes. ip enable Enables IPv4 Support. ip route gateway <GATEWAY-ADDR> Sets the controller's gateway address. ip name-server <DNS-ADDR> [<DNS-ADDR>] Sets the controller's DNS servers. Use a space ( ) to separate the primary and secondary DNS servers. ip addr <IP-ADDR> <NET-MASK> Sets the controller's IP address and netmask. Use a space ( ) to separate the IP address and netmask. ip mode dhcp Sets the controller's IP address mode to 'DHCP'. ip mode static Sets the controller's IP address mode to 'Static'. show Displays current system interface settings.

David.

Re: How to configure eth0 on R550?

cmak — Tue, 07 Jul 2026 09:32:43 GMT

I think it is because you have logged in your master AP.
Pls use command "ap-mode"
Then you can use command like "get eth"

Re: How to configure eth0 on R550?

iwx — Tue, 07 Jul 2026 11:51:18 GMT

Excellent, cmak!

It works as you have pointed out.

Thank you.

topic Re: How to configure eth0 on R550? in Access Points - Indoor and Outdoor

How to configure eth0 on R550?

Re: How to configure eth0 on R550?

Re: How to configure eth0 on R550?

Re: How to configure eth0 on R550?

Re: How to configure eth0 on R550?