https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/Using-DPSK-to-tag-vlans-how-to-handle-wired-clients-on-non/m-p/38353#M10847 We are a retirement community offering Wifi services to our residents in cottages using T300/1s. &nbsp;We've setup DPSK to isolate "subscriber" devices from each other by dynamically assigning VLANs. &nbsp;It has been working well up until a new issue appeared...we have a resident that has wired devices (an older TV, receiver, NAS box, and printer) that are not wireless. &nbsp; He has a Asus router running DD-WRT. &nbsp;I think I can configure his router as a bridge but am concerned that since the DPSK passphrase is tied to 1 mac address, the wired devices connected to the bridge will not be able to connect because they have unique mac addresses behind the bridge. &nbsp;Any ideas of how to work around this or am I forced to purchase another Ruckus AP and manually assign the VLAN to the ethernet port and run it to his switch? Thu, 04 Aug 2016 14:33:46 GMT kieth_hoover 2016-08-04T14:33:46Z https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/Using-DPSK-to-tag-vlans-how-to-handle-wired-clients-on-non/m-p/38353#M10847 We are a retirement community offering Wifi services to our residents in cottages using T300/1s. &nbsp;We've setup DPSK to isolate "subscriber" devices from each other by dynamically assigning VLANs. &nbsp;It has been working well up until a new issue appeared...we have a resident that has wired devices (an older TV, receiver, NAS box, and printer) that are not wireless. &nbsp; He has a Asus router running DD-WRT. &nbsp;I think I can configure his router as a bridge but am concerned that since the DPSK passphrase is tied to 1 mac address, the wired devices connected to the bridge will not be able to connect because they have unique mac addresses behind the bridge. &nbsp;Any ideas of how to work around this or am I forced to purchase another Ruckus AP and manually assign the VLAN to the ethernet port and run it to his switch? Thu, 04 Aug 2016 14:33:46 GMT https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/Using-DPSK-to-tag-vlans-how-to-handle-wired-clients-on-non/m-p/38353#M10847 kieth_hoover 2016-08-04T14:33:46Z https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/Using-DPSK-to-tag-vlans-how-to-handle-wired-clients-on-non/m-p/38354#M10848 So I did some testing and was able to get everything working: &nbsp;I followed the guide here:&nbsp;&nbsp;<A href="https://www.dd-wrt.com/wiki/index.php/Client_Bridged" rel="nofollow" target="_blank" title="Link https//wwwdd-wrtcom/wiki/indexphp/Client_Bridged">https://www.dd-wrt.com/wiki/index.php/Client_Bridged</A>&nbsp;and then had to run this command in the CLI on&nbsp;the Ruckus AP to get DHCP working on the bridged wired devices: &nbsp;set qos directedDHCP disable&nbsp;<BR /><BR />Tested communication both ways between wired &amp; wireless and to WAN and so far everything is working Thu, 04 Aug 2016 20:03:23 GMT https://community.ruckuswireless.com/t5/Access-Points-Indoor-and-Outdoor/Using-DPSK-to-tag-vlans-how-to-handle-wired-clients-on-non/m-p/38354#M10848 kieth_hoover 2016-08-04T20:03:23Z